Hahaho interactive pole
hadoopmarc·hahaho-interactive-pole·kicad/pole-electronics/pole-electronics.kicad_sch
About the Hahaho interactive pole PCB
Hahaho interactive pole is an open source ESP32 PCB design by hadoopmarc, published on GitHub under the AGPL-3.0 license. It is a board, with 38 components from 29 distinct parts.
Its main chip is the ESP32_30pin, from the ESP32 family. Other key parts include the SR501 PIR, PAM8610 module, dc/dc 5V, PCM5102A and DFplayer mp3. By type, the board carries 8 connectors, 7 ICs, 7 resistors, 3 diodes, 3 capacitors and 2 transistors.
It belongs with the audio and displays & leds designs in this gallery.
From the project
The joined membership of the Hahaho Foundation feels that the remaining prototypes can serve for applications with a higher fun factor and we will use the interactive pole as a project in which people of all skill-levels can participate. If you live near Utrecht and want to see t
The joined membership of the Hahaho Foundation feels that the remaining prototypes can serve for applications with a higher fun factor and we will use the interactive pole as a project in which people of all skill-levels can participate. If you live near Utrecht and want to see the pole in action, check our website for our biweekly meetings.
The figure above provides a schematic overview of the entire system (from the detailed documentation). The table below shows the connections between the various components and the ESP32 dev board.
Main components on the Hahaho interactive pole
Hahaho interactive pole bill of materials (BOM)
38 components, 29 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | SR501 PIR | Vishay_MINICAST-3Pin | U1, U3 |
| 1 | PAM8610 module | U2 | |
| 1 | dc/dc 5V | Converter_DCDC_RECOM_R-78E-0.5_THT | U4 |
| 1 | — | ESP32_30pin | U5 |
| 1 | PCM5102A | U6 | |
| 1 | DFplayer mp3 | MODULE_DFR0299 | U7 |
| 1 | Stroboscope | M1 | |
| 1 | BC547 | Q1 | |
| 1 | BD137 | Q2 | |
| 2 | Conn_01x04_Shielded | J1, J4 | |
| 1 | Conn_01x06_Socket | J2 | |
| 1 | Conn_01x06_Pin | J3 | |
| 1 | — | J5 | |
| 1 | Screw_Terminal_01x02 | J6 | |
| 2 | Screw_Terminal_01x15 | J7, J8 | |
| 1 | 12V 10.000 mAh? | BT1 | |
| 1 | Buzzer | BZ1 | |
| 1 | 3A | F1 | |
| 2 | Speaker | LS1, LS2 | |
| 1 | Red button | SW1 |
Show 9 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | — | SW2 | |
| 2 | NeoPixel | D1, D2 | |
| 1 | 1N4003 | D_DO-41_SOD81_P10.16mm_Horizontal | D3 |
| 2 | 100 uF | C1, C2 | |
| 1 | 100 nF | C3 | |
| 4 | 1k8 | R1, R2, R3, R4 | |
| 1 | 220 | R5 | |
| 1 | 3k9 | R6 | |
| 1 | 390 | R7 |
Hahaho interactive pole design files
The KiCad project lives in the hadoopmarc/hahaho-interactive-pole repository on GitHub; these links point at the commit this page was built from.
Hahaho interactive pole: common questions
What microcontroller does the Hahaho interactive pole use?
The Hahaho interactive pole is built around the ESP32_30pin, from the ESP32 family.
How many components are on the Hahaho interactive pole?
38 components, from 29 distinct parts. The full bill of materials is listed on this page.
Where can I download the Hahaho interactive pole design files?
From the hadoopmarc/hahaho-interactive-pole repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Hahaho interactive pole design in my own project?
Yes, under the terms of its AGPL-3.0 license, which hadoopmarc chose for the repository.
Can I test firmware for the Hahaho interactive pole without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k