Esp32-c3-compact dip led
haya1010·esp32-c3-compact-dip-led
About the Esp32-c3-compact dip led PCB
Esp32-c3-compact dip led is an open source ESP32 PCB design by haya1010, published on GitHub. It is a 2-layer board measuring 50 × 78 mm, with 17 components from 15 distinct parts.
Its main chip is the RJP020N06T100, from the ESP32 family. Other key parts include the ESP32-C3-WROOM-02-N4 and LMR36510FADDAR. By type, the board carries 4 connectors, 2 ICs, 1 transistor, 1 inductor and 1 capacitor.
It belongs with the dev boards & breakouts designs in this gallery.
From the project
Compact ESP32-C3 2.54 mm breakout with selectable USB-C/DC power and one LED PWM MOSFET channel
ESP32-C3-WROOM-02を2.54 mmピッチで引き出し、5/12/24 VのDC入力またはUSB-C 5 Vで動かせる、1チャンネルLED PWM基板です。基板寸法は 50 × 78 mm。USB-Cは電源専用で、書き込みはM5Stack A105ヘッダから行います。
- DCジャック: 5.5/2.1 mm、センタープラス、5~24 V - USB-C: 5 V電源専用。D+/D-は未接続、CC1/CC2に各5.1 kΩ - 3.3 V電源: LMR36510(最大入力65 V)による直接降圧 - 降圧インダクタ: 22µH、定格2A、飽和電流3.1Aの低価格モールド品 - JP1: USB 5 VかDC入力を手動選択 - JP2: 基板内3.3 VかA105の3.3 Vを手動選択 - 書き込み: M5Stack A105用6ピン(GND、BOOT、EN、TXD、RXD、3V3) - LED出力: J3-1がLED+、J3-2がMOSFETでPWMされるLED- - PWM: GPIO4、N-MOSFET 1チャンネル - JLCPCBでSMD実装、DCジャック・端子台・ピンヘッダは手はんだ

Main components on the Esp32-c3-compact dip led
Esp32-c3-compact dip led bill of materials (BOM)
17 components, 15 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02-N4 | ESP32-C3-WROOM-02 | U1 |
| 1 | LMR36510FADDAR | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm | U2 |
| 1 | RJP020N06T100 | SOT-89-3 | Q1 |
| 1 | PJ-102A compatible 5.5/2.1mm | BarrelJack_Horizontal | J1 |
| 1 | C165948 USB-C POWER ONLY | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | LED OUT | TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J3 |
| 1 | M5STACK A105 | PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | C23630 2.2uF 50V | C_1206_3216Metric | CIN1 |
| 1 | C282519 220nF 100V | C_0603_1608Metric | CIN2 |
| 2 | C45783 22uF 10V | C_0805_2012Metric | COUT1, COUT2 |
| 1 | DIP LEFT | PinHeader_1x12_P2.54mm_Vertical | JH1 |
| 1 | DIP RIGHT | PinHeader_1x12_P2.54mm_Vertical | JH2 |
| 2 | C23186 5.1k 1% | R_0603_1608Metric | RCC1, RCC2 |
| 1 | C49009349 ZETC404020S-220MT-LF 22uH 2A Isat3.1A | ZETC404020S-220MT-LF | L1 |
| 1 | 10uF 10V | C_0805_2012Metric | C3V3 |
Esp32-c3-compact dip led design files
The KiCad project lives in the haya1010/esp32-c3-compact-dip-led repository on GitHub; these links point at the commit this page was built from.
Esp32-c3-compact dip led: common questions
What microcontroller does the Esp32-c3-compact dip led use?
The Esp32-c3-compact dip led is built around the RJP020N06T100, from the ESP32 family.
How big is the Esp32-c3-compact dip led PCB?
The Esp32-c3-compact dip led measures 50 × 78 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-c3-compact dip led?
17 components, from 15 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32-c3-compact dip led design files?
From the haya1010/esp32-c3-compact-dip-led repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32-c3-compact dip led design in my own project?
The repository has no license, so all rights stay with haya1010. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-c3-compact dip led without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k