Esp32-c3-safe dip led controller
haya1010·esp32-c3-safe-dip-led-controller
About the Esp32-c3-safe dip led controller PCB
Esp32-c3-safe dip led controller is an open source ESP32 PCB design by haya1010, published on GitHub. It is a 2-layer board measuring 100 × 102 mm, with 53 components from 38 distinct parts.
Its main chip is the FDD5614P, from the ESP32 family. Other key parts include the ESP32-C3-WROOM-02-N4, LMR36510FADDAR, AP2112K-3.3TRG1, USBLC6-2SC6 and 74AHCT125D. By type, the board carries 5 ICs, 5 resistors, 4 transistors, 4 connectors, 4 diodes and 2 fuses.
From the project
Protected ESP32-C3 2.54 mm DIP controller with USB-C and 3-channel 5/12/24 V LED PWM outputs
KiCad 9 design for an ESP32-C3-WROOM-02-N4 controller with native USB-C programming, a protected 5/12/24 V input, a shared 3.3 V controller supply, and three low-side PWM LED outputs. SMD parts are selected for JLCPCB PCBA; the fuse holder, power connectors, LED terminals and 2.54 mm headers are hand soldered.
The two Schottky diodes form automatic source ORing. They allow either USB-C or the external adapter to run the controller while preventing the external supply from feeding into the computer's USB port. Both paths deliberately meet at SYS5V` and use the same AP2112K 3.3 V regulator.
Main components on the Esp32-c3-safe dip led controller
Esp32-c3-safe dip led controller bill of materials (BOM)
53 components, 38 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-WROOM-02-N4 | ESP32-C3-WROOM-02 | U1 |
| 1 | LMR36510FADDAR | SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm | U2 |
| 1 | AP2112K-3.3TRG1 | SOT-23-5 | U3 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U4 |
| 1 | 74AHCT125D | SOIC-14_3.9x8.7mm_P1.27mm | U5 |
| 1 | FDD5614P | TO-252-2 | Q0 |
| 3 | AO4268 | SOIC-8_3.9x4.9mm_P1.27mm | Q1, Q2, Q3 |
| 1 | PJ-102A compatible DC jack | BarrelJack_Horizontal | J1 |
| 1 | C165948 USB-C USB2 DEVICE | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | USB-UART 3V3 | PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | 5-24V HIGH-CURRENT INPUT | TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | J7 |
| 1 | C23630 2.2uF 50V | C_1206_3216Metric | CIN1 |
| 1 | C282519 220nF 100V | C_0603_1608Metric | CIN2 |
| 2 | C15850 10uF 10V | C_0805_2012Metric | CLDO1, CLDO2 |
| 2 | C45783 22uF 10V | C_0805_2012Metric | COUT1, COUT2 |
| 1 | BZT52C5V1 | D_SOD-123 | DZ5 |
| 1 | C47345582 0.50A 30V PTC | Fuse_1206_3216Metric | F1 |
| 1 | C70069 0.50A 6V PTC | Fuse_1206_3216Metric | F2 |
| 1 | DIP LEFT | PinHeader_1x12_P2.54mm_Vertical | JH1 |
| 1 | DIP RIGHT | PinHeader_1x12_P2.54mm_Vertical | JH2 |
Show 18 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LED CH1 | TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | JLED1 |
| 1 | LED CH2 | TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | JLED2 |
| 1 | LED CH3 | TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | JLED3 |
| 2 | C23186 5.1k 1% | R_0603_1608Metric | RCC1, RCC2 |
| 3 | 68R | R_0603_1608Metric | RG1, RG2, RG3 |
| 3 | 10K 10k | R_0603_1608Metric | RIN1, RIN2, RIN3 |
| 3 | 100K 100k | R_0603_1608Metric | RPD1, RPD2, RPD3 |
| 2 | 22R | R_0603_1608Metric | RUSB1, RUSB2 |
| 1 | C79172 RESET | SW_SPST_EVQP7A | SW1 |
| 1 | C79172 BOOT | SW_SPST_EVQP7A | SW2 |
| 1 | BZT52C12 | D_SOD-123 | D0 |
| 1 | SMBJ26A | D_SMB | D1 |
| 2 | SS34 | D_SMA | D2, D3 |
| 1 | C408353 22uH >=1.5A | L_Vishay_IHLP-1616 | L1 |
| 1 | 10uF 10V | C_0805_2012Metric | C3V3 |
| 1 | 100K 100k | R_0603_1608Metric | R0 |
| 2 | 10k | R_0603_1608Metric | R2S, R8S |
| 2 | 10K 10k | R_0603_1608Metric | R4, R5 |
Esp32-c3-safe dip led controller design files
The KiCad project lives in the haya1010/esp32-c3-safe-dip-led-controller repository on GitHub; these links point at the commit this page was built from.
Esp32-c3-safe dip led controller: common questions
What microcontroller does the Esp32-c3-safe dip led controller use?
The Esp32-c3-safe dip led controller is built around the FDD5614P, from the ESP32 family.
How big is the Esp32-c3-safe dip led controller PCB?
The Esp32-c3-safe dip led controller measures 100 × 102 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-c3-safe dip led controller?
53 components, from 38 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32-c3-safe dip led controller design files?
From the haya1010/esp32-c3-safe-dip-led-controller repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32-c3-safe dip led controller design in my own project?
The repository has no license, so all rights stay with haya1010. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32-c3-safe dip led controller without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k