Esp32 lps25hb

HeyPCB·esp32-sensors-1·boards/lps25hb/kicad/esp32_lps25hb.kicad_pcb

Esp32 lps25hb PCB layout, top view — open source ESP32 board by HeyPCB

About the Esp32 lps25hb PCB

Esp32 lps25hb is an open source ESP32 PCB design by HeyPCB, published on GitHub under the CERN-OHL-S-2.0 license. It is a 4-layer board measuring 30 × 48 mm, with 24 components from 19 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the USBLC6-2SC6, AP2112K-3.3TRG1 and LPS25HBTR. By type, the board carries 8 capacitors, 7 resistors, 4 ICs, 2 switches, 2 diodes and 1 connector.

It belongs with the sensors and iot & wireless designs in this gallery.

From the project

ESP32-S3 boards, one sensor each: KiCad 10, JLCPCB-ready, CERN-OHL-S-2.0

An ESP32-S3 board with ST LPS25HB MEMS pressure sensor: USB-C, Wi-Fi and Bluetooth LE, ready to flash.

Not fabricated, assembled or powered. Every number on this page is measured by KiCad 10 on the files in this folder; the full measurements are in report.json.

A small ESP32-S3 development board built around one sensor: ST LPS25HB MEMS pressure sensor. Plug in USB-C, flash it from Arduino, ESP-IDF or MicroPython over the ESP32-S3's native USB, and read the sensor. One of the HeyPCB ESP32 sensor series: the same ESP32-S3 template with a different sensor on each board. Designed with the…

Esp32 lps25hb, from the project README
From the project README

Main components on the Esp32 lps25hb

Esp32 lps25hb bill of materials (BOM)

24 components, 19 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
USBLC6-2SC6
U1
1
AP2112K-3.3TRG1
AP2112K-3.3
U2
1
ESP32-S3-WROOM-1-N16R8
U3
1
LPS25HBTR
U4
1
TYPE-C-31-M-12
USB-C
J1
1
TS-1187A-B-A-B
BOOT
SW1
1
TS-1187A-B-A-B
RESET
SW2
1
NCD0603B1
Blue (IO48)
D1
1
KT-0603G
Green (PWR)
D2
1
CL21A106KAYNNNE
10uF
C1
3
CL10A105KB8NNNC
1uF
C2, C3, C6
1
CC0603KRX7R9BB104
100nF
C4
1
CL21A226MAQNNNE
22uF
C5
2
CL05B104KO5NNNC
100nF
C7, C8
2
0402WGF5101TCE
5.1k
R1, R2
1
0603WAF1002T5E
10k
R3
1
0603WAF1001T5E
1k
R4
1
0603WAF2201T5E
2.2k
R5
2
0603WAF4701T5E
4.7k
R6, R7

Esp32 lps25hb design files

The KiCad project lives in the HeyPCB/esp32-sensors-1 repository on GitHub; these links point at the commit this page was built from.

Esp32 lps25hb: common questions

What microcontroller does the Esp32 lps25hb use?

The Esp32 lps25hb is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the Esp32 lps25hb PCB?

The Esp32 lps25hb measures 30 × 48 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Esp32 lps25hb?

24 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Esp32 lps25hb design files?

From the HeyPCB/esp32-sensors-1 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Esp32 lps25hb design in my own project?

Yes, under the terms of its CERN-OHL-S-2.0 license, which HeyPCB chose for the repository.

Can I test firmware for the Esp32 lps25hb without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in esp32-sensors-1

Similar boards