RaspberryPiHat
HoldenHalucha·office-hours-beacon·hardware/raspberryPiHat/RaspberryPiHat.kicad_pcb
About the RaspberryPiHat PCB
RaspberryPiHat is an open source ESP32 PCB design by HoldenHalucha, published on GitHub. It is a 2-layer board measuring 54.3 × 29.3 mm, with 16 components from 9 distinct parts.
Its main chip is the ESP32-WROOM-32U, from the ESP32 family. By type, the board carries 5 capacitors, 4 resistors, 3 switches, 2 connectors, 1 IC and 1 diode.
From the project
EECS 473
Main components on the RaspberryPiHat
RaspberryPiHat bill of materials (BOM)
16 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32U | ESP32-WROOM-32U | U1 |
| 1 | RASPBERRY_PI_2_3 Raspberry_Pi_2_3 | PinHeader_2x20_P2.54mm_Vertical | J1 |
| 1 | CONN_01X04_SOCKET Conn_01x04_Socket | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 3 | SW_Push | SW_PUSH_6mm | SW1, SW2, SW3 |
| 1 | LED | LED_0603_1608Metric | D1 |
| 1 | 22UF 22uF | C_0603_1608Metric | C1 |
| 4 | 0.1UF 0.1uF | C_0603_1608Metric | C2, C3, C4, C5 |
| 3 | 10K 10k | R_0603_1608Metric | R1, R4, R5 |
| 1 | 150 | R_0603_1608Metric | R3 |
RaspberryPiHat design files
The KiCad project lives in the HoldenHalucha/office-hours-beacon repository on GitHub; these links point at the commit this page was built from.
RaspberryPiHat: common questions
What microcontroller does the RaspberryPiHat use?
The RaspberryPiHat is built around the ESP32-WROOM-32U, from the ESP32 family.
How big is the RaspberryPiHat PCB?
The RaspberryPiHat measures 54.3 × 29.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RaspberryPiHat?
16 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the RaspberryPiHat design files?
From the HoldenHalucha/office-hours-beacon repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the RaspberryPiHat design in my own project?
The repository has no license, so all rights stay with HoldenHalucha. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the RaspberryPiHat without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in office-hours-beacon
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k