Halo
humblef00ls·halo·kiCad_mk1/kiCad_mk1.kicad_sch
About the Halo PCB
Halo is an open source ESP32 PCB design by humblef00ls, published on GitHub under the Custom license license. It is a board, with 29 components from 25 distinct parts.
Its main chip is the ESP32-C6-DevKitC-1, from the ESP32 family. By type, the board carries 6 connectors, 5 resistors, 4 crystals, 4 switches, 4 capacitors and 3 diodes.
It belongs with the iot & wireless and displays & leds designs in this gallery.
From the project
one esp32 to control them all
A glowy LED ring thing that got out of hand. Started as a voice-controlled desk lamp, now it's a smart home hub with presence detection, a security camera, and Zigbee control. Runs on ESP32-C6 + XIAO ESP32S3.
It's a smart LED controller that drives a ring of 45 RGBW NeoPixels with some nice animations. It also has:
- Voice control through Google Home - Zigbee coordinator for smart blinds - mmWave radar for presence detection - A camera that wakes up when someone's detected - A buzzer that plays melodies - More stuff planned (matrix display, 12V accent lights)
Main components on the Halo
Halo bill of materials (BOM)
29 components, 25 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C6-DevKitC-1 | ESP32-C6-DevKitC-1 | U2 |
| 1 | Q_NMOS_GDS | Q1 | |
| 1 | NeoPixel_Ring_1 | X1 | |
| 1 | NeoPixel_Ring_2 | X2 | |
| 1 | NeoPixel_Ring_3 | X3 | |
| 1 | NeoPixel_Ring_4 | X4 | |
| 1 | Barrel_Jack | J1 | |
| 2 | DCDC_BOOST | J3, J5 | |
| 1 | RADAR | J4 | |
| 1 | ANGEL | J6 | |
| 1 | MATRIX | J7 | |
| 1 | MELODY_MAKER | BZ1 | |
| 1 | ACTION1 | SW1 | |
| 1 | ACTION2 | SW2 | |
| 1 | ACTION3 | SW3 | |
| 1 | RotaryEncoder_Switch | SW4 | |
| 1 | FLARE | D1 | |
| 2 | 1N5819 | D2, D3 | |
| 1 | 1kuF | C1 | |
| 1 | 470µF | C2 |
Show 5 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 100µF | C3 | |
| 1 | 100nF | C4 | |
| 1 | 330Ω | R1 | |
| 1 | 1kΩ | R2 | |
| 3 | 10kΩ | R3, R4, R5 |
Halo design files
The KiCad project lives in the humblef00ls/halo repository on GitHub; these links point at the commit this page was built from.
- SchematickiCad_mk1/kiCad_mk1.kicad_sch
Halo: common questions
What microcontroller does the Halo use?
The Halo is built around the ESP32-C6-DevKitC-1, from the ESP32 family.
How many components are on the Halo?
29 components, from 25 distinct parts. The full bill of materials is listed on this page.
Where can I download the Halo design files?
From the humblef00ls/halo repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Halo design in my own project?
It is published under Custom license, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Halo without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k