HardLabs

Arduino Battery Powered clone with extended EEPROM and clock

Ikarthikmb·Circuit-Designs·5_Project_BACEE/5-Project BACEE.kicad_pcb

Arduino Battery Powered clone with extended EEPROM and clock PCB layout, top view — open source AVR/Arduino board by Ikarthikmb

About the Arduino Battery Powered clone with extended EEPROM and clock PCB

Arduino Battery Powered clone with extended EEPROM and clock is an open source AVR/Arduino PCB design by Ikarthikmb, published on GitHub. It is a 2-layer board measuring 42.2 × 30.5 mm, with 17 components from 15 distinct parts.

Its main chip is the ATMEGA328P-AU, from the AVR/Arduino family. Other key parts include the DS1377_PDv2 and 24LC1025. By type, the board carries 4 ICs, 4 connectors, 3 capacitors, 2 crystals, 2 resistors and 1 battery holder.

It belongs with the power & battery and dev boards & breakouts designs in this gallery.

From the project

Schematics and PCB designs implemented in Kicad.

- Converts the input ac/dc voltage(which does not exceed 35V) to output of 5 volts. This can be used to power circuits that require 5V as input supply for example Arduino(Requires 5V input power supply). - Connections: Connect a input power supply to the jack and the output is obtained fron pin heads. - To view/modify the source file, download the repository and navigate to 1-Breadboard Power Supply folder and open the bread power supply schematic.pro project file in KiCAD.

Arduino Battery Powered clone with extended EEPROM and clock, from the project README
From the project README

Main components on the Arduino Battery Powered clone with extended EEPROM and clock

DS1377_PDv224LC1025ATMEGA328P-AU

Arduino Battery Powered clone with extended EEPROM and clock bill of materials (BOM)

17 components, 15 distinct parts.

QtyPartRefs
1
DS1377_PDv2
U1
2
24LC1025
U2, U3
1
ATMEGA328P-AU
U4
1
Crystal 32 MHz
Y1
1
Crystal 16MHz
Y2
1
Serial
J1
1
Digital pins
J2
1
ICSP
J3
1
I2C
J4
1
Battery 3V
BT1
1
LED
D1
2
22pF
C1, C2
1
10uF
C3
1
330Ohm
R1
1
10KOhm
R2

Arduino Battery Powered clone with extended EEPROM and clock design files

The KiCad project lives in the Ikarthikmb/Circuit-Designs repository on GitHub; these links point at the commit this page was built from.

Arduino Battery Powered clone with extended EEPROM and clock: common questions

What microcontroller does the Arduino Battery Powered clone with extended EEPROM and clock use?

The Arduino Battery Powered clone with extended EEPROM and clock is built around the ATMEGA328P-AU, from the AVR/Arduino family.

How big is the Arduino Battery Powered clone with extended EEPROM and clock PCB?

The Arduino Battery Powered clone with extended EEPROM and clock measures 42.2 × 30.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Arduino Battery Powered clone with extended EEPROM and clock?

17 components, from 15 distinct parts. The full bill of materials is listed on this page.

Where can I download the Arduino Battery Powered clone with extended EEPROM and clock design files?

From the Ikarthikmb/Circuit-Designs repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Arduino Battery Powered clone with extended EEPROM and clock design in my own project?

The repository has no license, so all rights stay with Ikarthikmb. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Arduino Battery Powered clone with extended EEPROM and clock without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in Circuit-Designs

Similar boards