Maxbox
ios-cv·maxbox·electronics/v1/maxbox/maxbox.kicad_pcb
About the Maxbox PCB
Maxbox is an open source ESP32 PCB design by ios-cv, published on GitHub under the AGPL-3.0 license. It is a 4-layer board measuring 99 × 99 mm, with 104 components from 42 distinct parts.
Its main chip is the ESP32-WROOM-32E-N4, from the ESP32 family. Other key parts include the LMR33630ARNXT, MFRC522 and SN65HVD230. By type, the board carries 44 resistors, 35 capacitors, 10 diodes, 4 ICs, 3 transistors and 3 inductors.
It belongs with the iot & wireless and rf & radio designs in this gallery.
From the project
An in car telemetry and access management box consisting of PCB design, firmware and case.
MaxBox open-source hardware ====================
This repository is for the 3D design files, KiCad PCB design/Gerber files, and ESP-IDF firmware files to produce a MaxBox control box. This takes the form of a 100mm diameter circular PCB with a Mifare antenna, buck converter capable of up to 36V DC input, RGB LEDs, high speed CAN bus transceiver, an ESP32-WROVER castellated module incorporating a Bluetooth and WiFi antenna, and GPIO to connect buttons and relays.
Main components on the Maxbox
Maxbox bill of materials (BOM)
104 components, 42 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LMR33630ARNXT | RNX0012B_VQFN-HR | U1 |
| 1 | MFRC522 | VQFN-32-1EP_5x5mm_P0.5mm_EP3.5x3.5mm_ThermalVias | U2 |
| 1 | ESP32-WROOM-32E-N4 | ESP32-WROOM-32 | U3 |
| 1 | SN65HVD230 | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 3 | AO3400A | SOT-23 | Q1, Q2, Q3 |
| 1 | 27.12MHZ 27.12MHz | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | TC2030-IDC-NL_ESP | Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J1 |
| 1 | C99277 PICOBLADE | Molex_PicoBlade_53261-0671_1x06-1MP_P1.25mm_Horizontal | J2 |
| 1 | Antenna_Loop | 95mm-3turn-antenna | AE1 |
| 1 | C318884 RESET | XKB_TS-1187A-B-A-B | SW1 |
| 1 | C72043 STATUS | LED_0603_1608Metric | D1 |
| 1 | NUP2105L | SOT-23 | D3 |
| 8 | C727905 RGBLED | LED_FM-Z2727RGBA-SH | D4, D5, D6, D7, D8, D9, D10, D11 |
| 1 | 6.8UH 6.8uH | L_Cenker_CKST0603 | L1 |
| 2 | 470NH 470nH | L_0805_2012Metric | L2, L3 |
| 1 | C440198 10u 50V | C_0805_2012Metric | C1 |
| 1 | C29823 4.7u 50V | C_1206_3216Metric | C2 |
| 2 | C307331 100n 50V | C_0402_1005Metric | C3, C4 |
| 2 | 1u | C_0402_1005Metric | C5, C7 |
| 10 | 100N 100n | C_0402_1005Metric | C6, C10, C12, C13, C14, C20, C26, C27 +2 |
Show 22 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 22U 22u | C_0805_2012Metric | C8, C9, C33, C34 |
| 3 | 10U 10u | C_0402_1005Metric | C11, C25, C29 |
| 2 | 12P 12p | C_0805_2012Metric | C15, C16 |
| 2 | 122PF 122pF | C_0603_1608Metric | C17, C18 |
| 2 | 41.8PF 41.8pF | C_0805_2012Metric | C19, C22 |
| 1 | 1n | C_0402_1005Metric | C21 |
| 2 | 82.8PF 82.8pF | C_0805_2012Metric | C23, C24 |
| 1 | 10P 10p | C_0402_1005Metric | C28 |
| 2 | 560P 560p | C_0402_1005Metric | C31, C32 |
| 1 | C25741 100k 1% | R_0402_1005Metric | R1 |
| 1 | C23172 43.2k 1% | R_0603_1608Metric | R2 |
| 1 | 1k | R_0402_1005Metric | R3 |
| 2 | 2.7K 2.7k | R_0603_1608Metric | R4, R17 |
| 2 | 3.24R | R_0402_1005Metric | R5, R6 |
| 2 | 12K | R_0402_1005Metric | R7, R9 |
| 5 | 220R | R_0402_1005Metric | R8, R10, R18, R19, R20 |
| 1 | 470K | R_0402_1005Metric | R11 |
| 1 | 100K | R_0402_1005Metric | R12 |
| 2 | 470R | R_0402_1005Metric | R13, R14 |
| 2 | 100R | R_0402_1005Metric | R15, R16 |
| 8 | 75R | R_0402_1005Metric | R21, R24, R27, R30, R33, R36, R39, R42 |
| 16 | 33R | R_0402_1005Metric | R22, R23, R25, R26, R28, R29, R31, R32 +8 |
Maxbox design files
The KiCad project lives in the ios-cv/maxbox repository on GitHub; these links point at the commit this page was built from.
Maxbox: common questions
What microcontroller does the Maxbox use?
The Maxbox is built around the ESP32-WROOM-32E-N4, from the ESP32 family.
How big is the Maxbox PCB?
The Maxbox measures 99 × 99 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Maxbox?
104 components, from 42 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Maxbox design files?
From the ios-cv/maxbox repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Maxbox design in my own project?
Yes, under the terms of its AGPL-3.0 license, which ios-cv chose for the repository.
Can I test firmware for the Maxbox without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k