Foc ex
IpinZhu·foc-esc·hardware/foc-expansion/foc-ex.kicad_pcb
About the Foc ex PCB
Foc ex is an open source ESP32 PCB design by IpinZhu, published on GitHub under the MIT license. It is a 2-layer board measuring 50 × 70 mm, with 5 components from 5 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the ESP32-C3-WROOM-02. By type, the board carries 2 ICs, 1 connector, 1 switch and 1 capacitor.
From the project
这是一个基于 STM32G473RC 的实验性三相 PMSM/BLDC 电机控制平台。仓库包含驱动板设计,以及使用 Rust 2024 + Embassy 实现的电流控制型磁场定向控制(FOC)固件。
这是一个基于 STM32G473RC 的实验性三相 PMSM/BLDC 电机控制平台。仓库包含驱动板设计,以及使用 Rust 2024 + Embassy 实现的电流控制型磁场定向控制(FOC)固件。
当前固件位于 software/firmware,目标芯片为 STM32G473RC:
- TIM1 中心对齐互补 PWM,输出引脚为 PA8/PA9/PA10 和 PB13/PB14/PB15。 - 配置的 PWM 频率:100 kHz。 - 配置的死区时间:在 170 MHz 定时器时钟下为 200 ns。 - 占空比范围:5%–95%。 - 通过 INA240A2 放大器和 0.5 mΩ 分流电阻进行三相电流反馈。 - 由定时器触发 ADC,对相电流、VBUS 和 TMP235 温度传感器进行采样。 - 支持电流 FOC、速度 FOC、开环控制、启动电流偏置校准、SVPWM、遥测和软件故障处理。 - 带版本和 CRC 的双槽 Flash 参数持久化:上电自动加载,UART param ... 命令和 CAN 参数帧可读取、设置、保存或恢复出厂参数。 - 电机参数自整定(Auto-Tune):autotune start 一键完成 Rs/L/磁链辨识、电流环 PI 计算与阶跃验证、开环同步校验和观测器参数配置,结果保存为带 CRC 的电机参数档案,重启后自动应用。 -…
Main components on the Foc ex
Foc ex bill of materials (BOM)
5 components, 5 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U2 |
| 1 | Conn_01x02 | PinHeader_2x12_P2.54mm_Vertical | J1 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 1 | C_Small | CP_Radial_D6.3mm_P2.50mm | C1 |
Foc ex design files
The KiCad project lives in the IpinZhu/foc-esc repository on GitHub; these links point at the commit this page was built from.
Foc ex: common questions
What microcontroller does the Foc ex use?
The Foc ex is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Foc ex PCB?
The Foc ex measures 50 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Foc ex?
5 components, from 5 distinct parts. The full bill of materials is listed on this page.
Where can I download the Foc ex design files?
From the IpinZhu/foc-esc repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Foc ex design in my own project?
Yes, under the terms of its MIT license, which IpinZhu chose for the repository.
Can I test firmware for the Foc ex without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in foc-esc
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k