S3Forge-V1
izaanhussain·S3Forge-V1·PCB/S3Forge-V1.kicad_pcb
About the S3Forge-V1 PCB
S3Forge-V1 is an open source ESP32 PCB design by izaanhussain, published on GitHub under the MIT license. It is a 2-layer board measuring 70 × 55 mm, with 19 components from 16 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 6 resistors, 4 capacitors, 3 connectors, 2 ICs, 2 switches and 2 diodes.
It belongs with the dev boards & breakouts and power & battery designs in this gallery.
From the project
A custom ESP32-S3 development board with USB-C, GPIO expansion, I²C/SPI/UART interfaces, battery input, and onboard power management.
A custom ESP32-S3 development board that I designed in KiCad.
I want to make a small dev board with USB-C, some GPIO expansion, and onboard power management so that it's usable for real embedded projects.
Main microcontroller: ESP32-S3-WROOM-1 USB-C connection GPIO expansion headers I²C, SPI and UART support through GPIO Reset and Boot buttons Power and user LEDs AMS1117-3.3V regulator Compact PCB layout in KiCad
Main components on the S3Forge-V1
S3Forge-V1 bill of materials (BOM)
19 components, 16 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | GPIO_LEFT | PinHeader_1x20_P2.54mm_Vertical | J2 |
| 1 | GPIO_RIGHT | PinHeader_1x20_P2.54mm_Vertical | J3 |
| 1 | RESET | SW_NKK_GW12LJP | SW1 |
| 1 | BOOT | SW_NKK_GW12LJP | SW2 |
| 1 | POWER | LED_0805_2012Metric | D1 |
| 1 | USER | LED_0805_2012Metric | D2 |
| 2 | 10uF | C_0805_2012Metric | C1, C2 |
| 1 | 100nF | C_0805_2012Metric | C3 |
| 1 | 1uF | C_0805_2012Metric | C4 |
| 2 | 10k | R_0805_2012Metric | R1, R2 |
| 2 | 5.1kΩ | R_0805_2012Metric | R3, R4 |
| 1 | 1k | R_0805_2012Metric | R5 |
| 1 | 330R | R_0805_2012Metric | R6 |
S3Forge-V1 design files
The KiCad project lives in the izaanhussain/S3Forge-V1 repository on GitHub; these links point at the commit this page was built from.
- LayoutPCB/S3Forge-V1.kicad_pcb
- SchematicPCB/S3Forge-V1.kicad_sch
- BOMProduction/BOM.csv
S3Forge-V1: common questions
What microcontroller does the S3Forge-V1 use?
The S3Forge-V1 is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the S3Forge-V1 PCB?
The S3Forge-V1 measures 70 × 55 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the S3Forge-V1?
19 components, from 16 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the S3Forge-V1 design files?
From the izaanhussain/S3Forge-V1 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the S3Forge-V1 design in my own project?
Yes, under the terms of its MIT license, which izaanhussain chose for the repository.
Can I test firmware for the S3Forge-V1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k