Rusty Allstar
jaenulton·Rusty_Allstar·hardware/kicad/rusty_allstar_micronode.kicad_sch
About the Rusty Allstar PCB
Rusty Allstar is an open source ESP32 PCB design by jaenulton, published on GitHub. It is a board, with 7 components from 7 distinct parts.
Its main chip is the ESP32-WROOM-32E, from the ESP32 family. Other key parts include the SA818S-U, PCM5102A and AP2112K-3.3. By type, the board carries 4 ICs, 2 connectors and 1 transistor.
It belongs with the audio designs in this gallery.
From the project
Next-generation AllStarLink / app_rpt engine rewritten in Rust for embedded systems (ESP32) and bare-metal nodes
A high-performance, memory-safe, embedded-ready rewrite of the AllStarLink amateur radio repeater and node engine in Rust.
AllStarLink (ASL) is a popular amateur radio VoIP linking network based on Asterisk PBX with the apprpt` channel driver. While groundbreaking for its time, Asterisk was designed as a corporate telephony switch, forcing repeaters to act as "telephone calls" wrapped in complex dialplans, DAHDI kernel modules, and decades of monolithic C code with POSIX mutex locks.
Main components on the Rusty Allstar
Rusty Allstar bill of materials (BOM)
7 components, 7 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-WROOM-32E | ESP32-WROOM-32 | U1 |
| 1 | SA818S-U | NiceRF_SA818 | U2 |
| 1 | PCM5102A | TSSOP-20_4.4x6.5mm_P0.65mm | U3 |
| 1 | AP2112K-3.3 | SOT-23-5 | U4 |
| 1 | 2N7002 | SOT-23 | Q1 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_GCT_USB4105 | J1 |
| 1 | SMA_RF_OUT | SMA_Amphenol_132134_EdgeMount | J2 |
Rusty Allstar design files
The KiCad project lives in the jaenulton/Rusty_Allstar repository on GitHub; these links point at the commit this page was built from.
Rusty Allstar: common questions
What microcontroller does the Rusty Allstar use?
The Rusty Allstar is built around the ESP32-WROOM-32E, from the ESP32 family.
How many components are on the Rusty Allstar?
7 components, from 7 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Rusty Allstar design files?
From the jaenulton/Rusty_Allstar repository on GitHub, which has the schematic, a netlist and the BOM; the links under Design files point to each one.
Can I use the Rusty Allstar design in my own project?
The repository has no license, so all rights stay with jaenulton. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Rusty Allstar without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k