SNAP Power Controller
jaisor·SNAP_Power_Controller
About the SNAP Power Controller PCB
SNAP Power Controller is an open source PCB design by jaisor, published on GitHub under the CERN-OHL-P-2.0 license. It is a 2-layer board measuring 52 × 29 mm, with 37 components from 27 distinct parts.
Other key parts include the CN3791 and INA3221. By type, the board carries 10 resistors, 9 connectors, 7 diodes, 6 capacitors, 2 ICs and 2 transistors.
It belongs with the power & battery, rf & radio and sensors designs in this gallery.
From the project
KiCad 10 solar 1S LiPo charger: CN3791 MPPT, up to 4x 5V panels, INA219 I2C power monitor
A small solar charger board for a single-cell (1S) Li-ion/LiPo battery, built for solar-powered LoRa mesh nodes such as SNAP v1.2. Up to four 5V panels feed a CN3791 MPPT buck charger. A switched output powers the node, and an INA3221 reports voltage and current on three channels over I2C.
This controller is meant for solar mesh nodes like the SNAP v1.2: Solar Node Adaptable Platform. It simplifies their build in three ways:

Main components on the SNAP Power Controller
SNAP Power Controller bill of materials (BOM)
37 components, 27 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CN3791 | SSOP-10_3.9x4.9mm_P1.00mm | U1 |
| 1 | INA3221 | Texas_RGV0016A_VQFN-16-1EP_4x4mm_P0.65mm_EP2.1x2.1mm | U2 |
| 2 | AO3401A | SOT-23 | Q1, Q2 |
| 4 | Solar_5V | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J1, J2, J3, J4 |
| 1 | LiPo_1S_4.2V | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J5 |
| 1 | VOUT | Molex_PicoBlade_53047-0210_1x02_P1.25mm_Vertical | J6 |
| 1 | SW_BATT | PinHeader_1x02_P2.54mm_Vertical | J7 |
| 1 | SW_LOAD | PinHeader_1x02_P2.54mm_Vertical | J8 |
| 1 | I2C_MCU | Molex_PicoBlade_53047-0410_1x04_P1.25mm_Vertical | J9 |
| 1 | SS34 | D_SMA | D2 |
| 1 | GREEN | LED_0603_1608Metric | D3 |
| 1 | RED | LED_0603_1608Metric | D4 |
| 4 | 1N5819W | D_SOD-123 | D5, D6, D7, D8 |
| 1 | 22uH | L_Bourns_SRN6045TA | L1 |
| 1 | 10uF/25V | C_1206_3216Metric | C1 |
| 2 | 100nF | C_0603_1608Metric | C2, C6 |
| 1 | 22uF/10V | C_1206_3216Metric | C3 |
| 1 | 220nF | C_0603_1608Metric | C4 |
| 1 | 100nF/25V | C_0603_1608Metric | C5 |
| 1 | 1k | R_0603_1608Metric | R1 |
Show 7 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 120R | R_0603_1608Metric | R2 |
| 1 | 267k 1% | R_0603_1608Metric | R3 |
| 1 | 100k 1% | R_0603_1608Metric | R4 |
| 1 | 0.15R 1% | R_1206_3216Metric | R5 |
| 2 | 0.1R 1% | R_1206_3216Metric | R6, R7 |
| 2 | 10k | R_0603_1608Metric | R8, R9 |
| 1 | 0.1R 1% | R_0603_1608Metric | R10 |
SNAP Power Controller design files
The KiCad project lives in the jaisor/SNAP_Power_Controller repository on GitHub; these links point at the commit this page was built from.
SNAP Power Controller: common questions
How big is the SNAP Power Controller PCB?
The SNAP Power Controller measures 52 × 29 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the SNAP Power Controller?
37 components, from 27 distinct parts. The full bill of materials is listed on this page.
Where can I download the SNAP Power Controller design files?
From the jaisor/SNAP_Power_Controller repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the SNAP Power Controller design in my own project?
Yes, under the terms of its CERN-OHL-P-2.0 license, which jaisor chose for the repository.
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kEinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2k