3-Axis-Holonomic-Drive-Robot
jbriceno225·3-Axis-Holonomic-Drive-Robot·PCB/Rev_A/KiCad_Project/KiwiDrive.kicad_pcb
About the 3-Axis-Holonomic-Drive-Robot PCB
3-Axis-Holonomic-Drive-Robot is an open source ESP32 PCB design by jbriceno225, published on GitHub under the MIT license. It is a 2-layer board measuring 143.3 × 125.7 mm, with 12 components from 8 distinct parts.
Its main chip is the ESP32-DEVKIT-V1, from the ESP32 family. Other key parts include the TB6612FNG and R-78E5.0-1.0. By type, the board carries 5 ICs and 4 connectors.
It belongs with the robotics & motion designs in this gallery.
Main components on the 3-Axis-Holonomic-Drive-Robot
3-Axis-Holonomic-Drive-Robot bill of materials (BOM)
12 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | TB6612FNG | TB6612FNG | U1, U2, U3 |
| 1 | R-78E5.0-1.0 | Converter_DCDC_RECOM_R-78E-0.5_THT | U4 |
| 1 | ESP32-DEVKIT-V1 | MODULE_ESP32_DEVKIT_V1 | U5 |
| 1 | SCREW_TERMINAL_01X02 Screw_Terminal_01x02 | AMASS_XT30PW-F_1x02_P2.50mm_Horizontal | J1 |
| 1 | CONN_01X10 Conn_01x10 | PinHeader_1x10_P2.54mm_Vertical | J2 |
| 1 | CONN_01X04 Conn_01x04 | PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | CONN_01X02 Conn_01x02 | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 3 | ~ | 25GA_Motor_Encoder_6Pin | DCmotorWithEncoder1, DCmotorWithEncoder2, DCmotorWithEncoder3 |
3-Axis-Holonomic-Drive-Robot design files
The KiCad project lives in the jbriceno225/3-Axis-Holonomic-Drive-Robot repository on GitHub; these links point at the commit this page was built from.
3-Axis-Holonomic-Drive-Robot: common questions
What microcontroller does the 3-Axis-Holonomic-Drive-Robot use?
The 3-Axis-Holonomic-Drive-Robot is built around the ESP32-DEVKIT-V1, from the ESP32 family.
How big is the 3-Axis-Holonomic-Drive-Robot PCB?
The 3-Axis-Holonomic-Drive-Robot measures 143.3 × 125.7 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the 3-Axis-Holonomic-Drive-Robot?
12 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the 3-Axis-Holonomic-Drive-Robot design files?
From the jbriceno225/3-Axis-Holonomic-Drive-Robot repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the 3-Axis-Holonomic-Drive-Robot design in my own project?
Yes, under the terms of its MIT license, which jbriceno225 chose for the repository.
Can I test firmware for the 3-Axis-Holonomic-Drive-Robot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k