Design2
Je0Dev·firstpcbs·design2/design2.kicad_pcb
About the Design2 PCB
Design2 is an open source ESP32 PCB design by Je0Dev, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 22 × 37 mm, with 11 components from 9 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AMS1117-3.3. By type, the board carries 3 ICs, 3 capacitors, 3 resistors, 1 switch and 1 diode.
From the project
tutorial pcbs,schematics designs
Main components on the Design2
Design2 bill of materials (BOM)
11 components, 9 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U2 |
| 1 | ~ | usb_pcb_connect | U3 |
| 1 | BOOT | SW_Tactile_SPST_NO_Straight_CK_PTS636Sx25SMTRLFS | SW1 |
| 1 | LED | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1 |
| 2 | 10u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 1 | 1u | C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 2 | 1K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2 |
| 1 | 10K | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3 |
Design2 design files
The KiCad project lives in the Je0Dev/firstpcbs repository on GitHub; these links point at the commit this page was built from.
- Layoutdesign2/design2.kicad_pcb
- Schematicdesign2/design2.kicad_sch
Design2: common questions
What microcontroller does the Design2 use?
The Design2 is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Design2 PCB?
The Design2 measures 22 × 37 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Design2?
11 components, from 9 distinct parts. The full bill of materials is listed on this page.
Where can I download the Design2 design files?
From the Je0Dev/firstpcbs repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Design2 design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which Je0Dev chose for the repository.
Can I test firmware for the Design2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in firstpcbs
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k