Bypass clean before shorter-22
About the Bypass clean before shorter-22 PCB
Bypass clean before shorter-22 is an open source RP2040/RP2350 PCB design by JesseLevine727, published on GitHub. It is a 4-layer board measuring 90 × 70 mm, with 58 components from 27 distinct parts.
Its main chip is the RP2040, from the RP2040/RP2350 family. Other key parts include the W25Q16JVSNIQ, AP2112K-3.3TRG1, VL53L1CXV0FY/1 and MAX98357AETE+T. By type, the board carries 23 capacitors, 19 resistors, 5 ICs, 3 connectors, 3 switches and 2 diodes.
It belongs with the audio and sensors designs in this gallery.
From the project
Open airnote.kicadpro in KiCad 9. The three editable schematic sheets and routed four-layer PCB are the canonical design. The current native checks report 0 ERC violations; 0 DRC violations, 0 unconnected items and 0 schematic/PCB parity issues**. These are software checks; a phy
Open airnote.kicadpro in KiCad 9. The three editable schematic sheets and routed four-layer PCB are the canonical design. The current native checks report 0 ERC violations; 0 DRC violations, 0 unconnected items and 0 schematic/PCB parity issues**. These are software checks; a physical board has not been built or tested.
- Schematic PDF - Board render - Assembly drawing, including component references - Four copper layers - Exact component BOM - Draft fabrication and assembly exports - Native ERC and DRC - Independent review
Main components on the Bypass clean before shorter-22
Bypass clean before shorter-22 bill of materials (BOM)
58 components, 27 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | RP2040 Raspberry Pi | QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1 |
| 1 | W25Q16JVSNIQ W25Q16JVSSIQ Winbond | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | AP2112K-3.3TRG1 AP2112K-3.3 Diodes Inc. | SOT-23-5 | U3 |
| 1 | VL53L1CXV0FY/1 STMicroelectronics | ST_VL53L1x | U4 |
| 1 | MAX98357AETE+T Analog Devices | MAX98357A_T1633_ADI_90-0031 | U5 |
| 1 | ABM8-272-T3 12MHz ABM8-272-T3 Abracon | Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | USB4105-GF-A-120 USB-C USB2.0 GCT | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | C32713271 SWD 3V3 GND DIO CLK RUN hanxia | PinHeader_1x05_P2.54mm_Vertical | J2 |
| 1 | C131337 SPEAKER 8ohm >=1W JST | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J3 |
| 1 | 1206L050YR 500mA hold PTC Littelfuse | Fuse_1206_3216Metric | F1 |
| 1 | PTV09A-4015F-B103 10k LINEAR VOLUME Bourns | Potentiometer_Bourns_PTV09A-1_Single_Vertical | RV1 |
| 1 | TL3342F160QG BOOTSEL E-Switch | SW_SPST_TL3342 | SW1 |
| 1 | TL3342F160QG RESET E-Switch | SW_SPST_TL3342 | SW2 |
| 1 | JS202011JCQN MUTE / PLAY C&K | SW_DPDT_CK_JS202011JCQN | SW3 |
| 1 | USBLC6-2SC6 STMicroelectronics | SOT-23-6 | D1 |
| 1 | LTST-C190KGKT GREEN STATUS Lite-On | LED_0603_1608Metric | D2 |
| 2 | CL10C150JB8NNNC 15p Samsung Electro-Mechanics | C_0603_1608Metric | C1, C2 |
| 15 | CC0603KRX7R9BB104 100n Yageo | C_0603_1608Metric | C3, C4, C5, C6, C7, C8, C9, C10 +7 |
| 4 | CL10A105KB8NNNC 1u Samsung Electro-Mechanics | C_0603_1608Metric | C13, C14, C16, C17 |
| 2 | CL21A475KAQNNNE 4.7u Samsung Electro-Mechanics | C_0805_2012Metric | C20, C22 |
Show 7 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 0603WAF1001T5E 1k UNI-ROYAL | R_0603_1608Metric | R1, R3, R17, R18 |
| 6 | 0603WAF1002T5E 10k UNI-ROYAL | R_0603_1608Metric | R2, R4, R10, R11, R14, R16 |
| 1 | 0603WAF100KT5E 1 UNI-ROYAL | R_0603_1608Metric | R5 |
| 4 | 0603WAF5101T5E 5.1k UNI-ROYAL | R_0603_1608Metric | R6, R7, R12, R13 |
| 2 | 0603WAF270JT5E 27 UNI-ROYAL | R_0603_1608Metric | R8, R9 |
| 1 | 0603WAF1003T5E 100k UNI-ROYAL | R_0603_1608Metric | R15 |
| 1 | 0603WAF1004T5E 1M UNI-ROYAL | R_0603_1608Metric | R19 |
Bypass clean before shorter-22 design files
The KiCad project lives in the JesseLevine727/AirNote repository on GitHub; these links point at the commit this page was built from.
Bypass clean before shorter-22: common questions
What microcontroller does the Bypass clean before shorter-22 use?
The Bypass clean before shorter-22 is built around the RP2040, from the RP2040/RP2350 family.
How big is the Bypass clean before shorter-22 PCB?
The Bypass clean before shorter-22 measures 90 × 70 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Bypass clean before shorter-22?
58 components, from 27 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Bypass clean before shorter-22 design files?
From the JesseLevine727/AirNote repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Bypass clean before shorter-22 design in my own project?
The repository has no license, so all rights stay with JesseLevine727. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Bypass clean before shorter-22 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.
More boards in AirNote
RP2040/RP2350Bypass clean before c5
90 × 70 mm58 parts4LNo license0
RP2040/RP2350Before final bypass
90 × 70 mm58 parts4LNo license0
RP2040/RP2350Airnote routing pass1
90 × 70 mm58 parts4LNo license0
RP2040/RP2350Local prewired
90 × 70 mm58 parts4LNo license0
RP2040/RP2350Before manual repair
90 × 70 mm58 parts4LNo license0
RP2040/RP2350AirNote
90 × 70 mm58 parts4LNo license0
RP2040/RP2350RP2040 Minimal Design Example
52 × 51 mm30 parts2LNo license0
Similar boards
RP2040/RP2350Open Book Abridged Edition
joeycastillo
85 × 115 mm29 parts2LCC-BY-SA-4.08.1k
RP2040/RP2350Corne
foostan
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7k
RP2040/RP2350Corne
277.2 × 107.5 mm164 parts2LCC-BY-4.07.7k
RP2040/RP2350Jitx design
gusmanb
55.5 × 65 mm26 parts4LGPL-3.05.0k
RP2040/RP2350LogicAnalyzer
57 × 55.2 mm6 parts2LGPL-3.05.0k
RP2040/RP2350Main
google
98 × 71 mm102 parts2LApache-2.02.9k