DUCKY
Ka6667·DUCKY·Hardware/DUCKY.kicad_pcb
About the DUCKY PCB
DUCKY is an open source ESP32 PCB design by Ka6667, published on GitHub. It is a 2-layer board measuring 77.7 × 85 mm, with 7 components from 7 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DFR0299. By type, the board carries 2 ICs, 1 speaker and 1 switch.
From the project
Then there are three screws for the outer mounting for the face of the case. I extened the holes a little bit outside the case to make it more stable (also use Socket Head Cap Screws):
Then there are three screws for the outer mounting for the face of the case. I extened the holes a little bit outside the case to make it more stable (also use Socket Head Cap Screws):
you can still use a washer if you want to install any other screws that has small heads. just make sure to keep everything fixed in its place!!
The small little cylinder on the right side is a body that will be used as a knob extender for the potentiometer (The hole on the side and the knob's postition, lenght and width are accurate based on the data sheet of the potentiometer)! The CAD desgin of the…
Main components on the DUCKY
DUCKY bill of materials (BOM)
7 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-DIP-SMD | U1 |
| 1 | DFR0299 | MODULE_DFR0299 | U2 |
| 1 | R_US | R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical | 1K1 |
| 1 | 4311 | MODULE_4311 | DS1 |
| 1 | Speaker | Speaker_CUI_CMR-1206S-67 | LS1 |
| 1 | R_Potentiometer | Potentiometer_Alps_RK097_Single_Horizontal | RV1 |
| 1 | SW_Push | SW_Tactile_Straight_KSA0Axx1LFTR | SW1 |
DUCKY design files
The KiCad project lives in the Ka6667/DUCKY repository on GitHub; these links point at the commit this page was built from.
- LayoutHardware/DUCKY.kicad_pcb
- SchematicHardware/DUCKY.kicad_sch
DUCKY: common questions
What microcontroller does the DUCKY use?
The DUCKY is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the DUCKY PCB?
The DUCKY measures 77.7 × 85 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the DUCKY?
7 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the DUCKY design files?
From the Ka6667/DUCKY repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the DUCKY design in my own project?
The repository has no license, so all rights stay with Ka6667. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the DUCKY without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k