Wirelight
kimtore·wirelight·nuled/pcb/nuled.kicad_pcb
About the Wirelight PCB
Wirelight is an open source ESP32 PCB design by kimtore, published on GitHub under the MIT license. It is a 2-layer board measuring 53.5 × 45.5 mm, with 34 components from 20 distinct parts.
Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the AMS1117-3.3, TPS2116DRL and SN74. By type, the board carries 11 capacitors, 10 resistors, 4 ICs, 4 diodes, 3 connectors and 1 transistor.
It belongs with the iot & wireless designs in this gallery.
From the project
LED strips powered by Arduino, Wi-Fi and MQTT.
NULED connects to WiFi and is configured via MQTT. It supports numerous effects, and does its best to perform accurate color gradients.
The WS2812 LEDs are driven using the SPI2 controller using DMA, and the signal output is on the GPIO8 port.
Notable crate dependencies: esp-hal family for hardware interfaces, embassy for async and network support, smoltcp as the network stack, and ws2812-spi and smart-leds as the WS2812 driver.
Main components on the Wirelight
Wirelight bill of materials (BOM)
34 components, 20 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U1 |
| 1 | TPS2116DRL | SOT-583-8 | U2 |
| 1 | ESP32-C3-MINI-1 | ESP32-C3-MINI-1 | U3 |
| 1 | SN74 | SOT-363_SC-70-6 | U4 |
| 1 | SI2302-TP | SOT-23 | Q1 |
| 1 | USB4125-GF-A | USB_C_Receptacle_GCT_USB4125-xx-x-0190_6P_TopMnt_Horizontal | J1 |
| 1 | PROGRAMMER | PinSocket_1x06_P2.54mm_Vertical | J2 |
| 1 | SK6812RGBW_HEADER | PinHeader_1x03_P2.54mm_Horizontal | J4 |
| 1 | 3314J-1-103E | Potentiometer_Bourns_3314J_Vertical | RV1 |
| 1 | SMBJ5.0CA | D_SMB | D1 |
| 3 | APT1608PGW | D_0603_1608Metric | D2, D3, D4 |
| 7 | 0.1u | C_0603_1608Metric | C1, C4, C6, C7, C8, C9, C12 |
| 1 | 22u | C_0603_1608Metric | C2 |
| 1 | 1u/16V(10%) | C_0603_1608Metric | C3 |
| 1 | 10u | C_0603_1608Metric | C5 |
| 1 | 470u/10V(20%) | CP_Elec_8x6.7 | C10 |
| 2 | 5k1 | R_0603_1608Metric | R1, R2 |
| 5 | 10k | R_0603_1608Metric | R3, R4, R5, R6, R9 |
| 1 | 150 | R_0603_1608Metric | R7 |
| 2 | 56 | R_0603_1608Metric | R8, R10 |
Wirelight design files
The KiCad project lives in the kimtore/wirelight repository on GitHub; these links point at the commit this page was built from.
- Layoutnuled/pcb/nuled.kicad_pcb
- Schematicnuled/pcb/nuled.kicad_sch
Wirelight: common questions
What microcontroller does the Wirelight use?
The Wirelight is built around the ESP32-C3-MINI-1, from the ESP32 family.
How big is the Wirelight PCB?
The Wirelight measures 53.5 × 45.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Wirelight?
34 components, from 20 distinct parts. The full bill of materials is listed on this page.
Where can I download the Wirelight design files?
From the kimtore/wirelight repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Wirelight design in my own project?
Yes, under the terms of its MIT license, which kimtore chose for the repository.
Can I test firmware for the Wirelight without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k