HardLabs

1002 EPROM EMU NG 2.1

Kris-Sekula·EPROM-EMU-NG·KiCad Sources/2.1/1002_EPROM_EMU_NG_2.1.kicad_pcb

1002 EPROM EMU NG 2.1 PCB layout, top view — open source AVR/Arduino board by Kris-Sekula

About the 1002 EPROM EMU NG 2.1 PCB

1002 EPROM EMU NG 2.1 is an open source AVR/Arduino PCB design by Kris-Sekula, published on GitHub under the Apache-2.0 license. It is a 2-layer board measuring 99.1 × 88.9 mm, with 38 components from 25 distinct parts.

Its main chip is the 1050-1001, from the AVR/Arduino family. Other key parts include the 74HC00, 74HC08, 25LC512-I/P, 296-36142-5 and 1450-1033. By type, the board carries 11 resistors, 10 ICs, 7 capacitors, 3 transistors, 3 diodes and 1 module.

It belongs with the usb & debug tools designs in this gallery.

From the project

EPROM Emulator Project with Arduino

Changed from using 2x32 SRAM to single 128k SRAM (only 64k used).

Firmware and software is the same for both desings, but the single SRAM has few pins less to solder :)

Main components on the 1002 EPROM EMU NG 2.1

74HC0074HC0825LC512-I/P296-36142-51450-103374HC541

1002 EPROM EMU NG 2.1 bill of materials (BOM)

38 components, 25 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
74HC00
U1
1
74HC08
U2
1
25LC512-I/P
25LC512
U3
3
296-36142-5
74HC595
U4, U5, U6
1
1450-1033
AS6C1008-55PCN
U7
3
74HC541
U9, U10, U11
1
1050-1001
Arduino Nano v3.0
M1
1
2N4401-AP
2N4401
Q1
1
BC557
2N4403
Q2
1
PMOS
Q3
1
2057-MHR-34-HUAS
IDC34
J1
1
POLYFUSE_50MA
Polyfuse_200mA
F1
1
450-1804
SW_Push
SW1
2
LED
D2, D3
1
BAT48
D5
1
P19513
10uF
C1
5
100NF
100nF
C2, C3, C4, C5, C6
1
445-173593-1
22nF
C7
2
330R
R1, R2
2
CF18JT10K0
10k
R3, R7
Show 5 more
QtyPartRefs
1
CF18JT4K70
4k7
R4
2
10R
R5, R6
1
10k
R8
2
4610X-1-103LF
10K
RN1, RN2
1
10K
RN3

1002 EPROM EMU NG 2.1 design files

The KiCad project lives in the Kris-Sekula/EPROM-EMU-NG repository on GitHub; these links point at the commit this page was built from.

1002 EPROM EMU NG 2.1: common questions

What microcontroller does the 1002 EPROM EMU NG 2.1 use?

The 1002 EPROM EMU NG 2.1 is built around the 1050-1001, from the AVR/Arduino family.

How big is the 1002 EPROM EMU NG 2.1 PCB?

The 1002 EPROM EMU NG 2.1 measures 99.1 × 88.9 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the 1002 EPROM EMU NG 2.1?

38 components, from 25 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the 1002 EPROM EMU NG 2.1 design files?

From the Kris-Sekula/EPROM-EMU-NG repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the 1002 EPROM EMU NG 2.1 design in my own project?

Yes, under the terms of its Apache-2.0 license, which Kris-Sekula chose for the repository.

Can I test firmware for the 1002 EPROM EMU NG 2.1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in EPROM-EMU-NG

Similar boards