Dumper

legendaryredfox·oscr_minimal·boards/16_bits/hardware-v1.3/dumper.kicad_pcb

Dumper PCB layout, top view — open source PIC board by legendaryredfox

About the Dumper PCB

Dumper is an open source PIC PCB design by legendaryredfox, published on GitHub under the Custom license license. It is a 2-layer board measuring 108 × 126 mm, with 36 components from 20 distinct parts.

Its main chip is the PIC12F629 (em soquete; snescic-lock-resync), from the PIC family. Other key parts include the Si5351_Module, LD1117V33 and Mega2560_R3_Shield. By type, the board carries 17 resistors, 8 capacitors, 3 ICs, 2 transistors, 1 module and 1 connector.

It belongs with the dev boards & breakouts and retro computing designs in this gallery.

From the project

Dumper de cartuchos SNES/NES/Famicom/Mega Drive/GBA (shield para Arduino Mega), baseado no OSCR

Versão v1.3 da placa 16bits`: shield 100% THT para Arduino Mega 2560 R3, só USB. Esta é a versão mais nova.

O 5V dos slots vai direto do Mega e não é cortado por software (o desligamento por software foi retirado, D139). Para trocar o cartucho, desligue a placa tirando o cabo USB do Mega; nunca com a USB ligada.

F1: fusível de vidro 5×20 mm de 500 mA (ação rápida) em suporte de clipes, opcional. O suporte é de furo passante (Littelfuse série 100 ou equivalente) e o fusível queimado se troca sem solda; fica em série com o 5 V que a placa recebe do Mega Um curto no cartucho queima o fusível e…

Dumper, from the project README
From the project README

Main components on the Dumper

Si5351_ModulePIC12F629 (em soquete; snescic-lock-resync)LD1117V33Mega2560_R3_Shield

Dumper bill of materials (BOM)

36 components, 20 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
Si5351_Module
U1
1
PIC12F629 (em soquete; snescic-lock-resync)
U2
1
LD1117V33
U3
1
Mega2560_R3_Shield
A1
1
IRF9540N
Q4
1
2N7000
Q5
1
TRAVA 3,3 V
J1
1
Fusivel 5x20 500mA
F1
1
MD_Slot
MD1
1
SNES_Slot
SNES1
1
LED 3mm
D1
1
470u/16V
C1
6
100n
C2, C3, C4, C5, C6, C7
1
10u/16V
C8
1
220R
R1
1
1k
R2
12
0R
R3, R4, R5, R6, R7, R8, R9, R10 +4
1
100k
R23
1
1k
R24
1
220R
R25

Dumper design files

The KiCad project lives in the legendaryredfox/oscr_minimal repository on GitHub; these links point at the commit this page was built from.

Dumper: common questions

What microcontroller does the Dumper use?

The Dumper is built around the PIC12F629 (em soquete; snescic-lock-resync), from the PIC family.

How big is the Dumper PCB?

The Dumper measures 108 × 126 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Dumper?

36 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Dumper design files?

From the legendaryredfox/oscr_minimal repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Dumper design in my own project?

It is published under Custom license, which limits how it may be reused; read the license before building on it.

Can I test firmware for the Dumper without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.

More boards in oscr_minimal

Similar boards