CableProbe
linuskjk·CableProbe·pcb/CableProbe.kicad_pcb
About the CableProbe PCB
CableProbe is an open source ESP32 PCB design by linuskjk, published on GitHub under the MIT license. It is a 2-layer board measuring 58.6 × 55.1 mm, with 10 components from 4 distinct parts.
Its main chip is the ESP32-DEVKITC, from the ESP32 family. By type, the board carries 6 resistors, 3 ICs and 1 LED.
It belongs with the power & battery and displays & leds designs in this gallery.
From the project
A custom ESP32-based tool to analyze and verify USB-C cables.
A custom ESP32-based tool to analyze and verify USB-C cables.
- ESP32 on a custom PCB - 2x USB-C modules linked to GPIOs - 128x64 SSD1306 OLED display - Basic resistor setup for pin pulling
Ever bought a pile of cheap USB-C cables from AliExpress only to find out they are bad? Or struggled to figure out which cable actually supports fast charging?
CableProbe was made to quickly sort through the cable drawer. It identifies the quality and features of almost any USB-C cable without needing a PC or complicated setup.
Main components on the CableProbe
CableProbe bill of materials (BOM)
10 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | ~ | usbc_bb | U1, U2 |
| 1 | ESP32-DEVKITC ESP32-DevKitC | ESP32-DevKitC | U3 |
| 1 | 128X64OLED SSD1306 | 128x64OLED | Brd1 |
| 6 | 1k Ohm | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3, R4, R5, R6 |
CableProbe design files
The KiCad project lives in the linuskjk/CableProbe repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/CableProbe.kicad_pcb
- Schematicpcb/CableProbe.kicad_sch
- BOMBOM.csv
CableProbe: common questions
What microcontroller does the CableProbe use?
The CableProbe is built around the ESP32-DEVKITC, from the ESP32 family.
How big is the CableProbe PCB?
The CableProbe measures 58.6 × 55.1 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CableProbe?
10 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the CableProbe design files?
From the linuskjk/CableProbe repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the CableProbe design in my own project?
Yes, under the terms of its MIT license, which linuskjk chose for the repository.
Can I test firmware for the CableProbe without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k