Portablehacker
linuskjk·portablehacker·pcb/final.kicad_pcb
About the Portablehacker PCB
Portablehacker is an open source ESP32 PCB design by linuskjk, published on GitHub under the MIT license. It is a 2-layer board measuring 44.6 × 132.8 mm, with 5 components from 4 distinct parts.
Its main chip is the ESP32-DEVKITC, from the ESP32 family. By type, the board carries 2 ICs, 2 resistors and 1 capacitor.
It belongs with the iot & wireless, power & battery and displays & leds designs in this gallery.
From the project
A portable hacking deceive made for fallout (hackclub)
Portable Hacker is a handheld device to test the security of WiFi networks and bluetooth.
- ESP32 preferably with antenna support - ESP8266 NodeMCU V3 - 0.91" Oled display (I2C) - Rotary encoder - PCB - 2x100k Ohm Resistors - 1x0.1uF capacitor
1. Assemble the PCB 2. Solder all components 3. Connect the OLED display 4. Connect the battery to the charger module. (B+/- to charger module and output of that to V+/GND pin) it is not on the pcb on purpose as this saves up a lot of space and still works perfectly fine (even better, as bc of this the battery placement is more flexible. Just click…
Main components on the Portablehacker
Portablehacker bill of materials (BOM)
5 components, 4 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | Untitled | U2 |
| 1 | ESP32-DEVKITC ESP32-DevKitC | ESP32-DevKitC | U3 |
| 1 | 0.1UF 0.1uF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C1 |
| 2 | 100K 100k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
Portablehacker design files
The KiCad project lives in the linuskjk/portablehacker repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/final.kicad_pcb
- Schematicpcb/final.kicad_sch
- BOMpcb/bom.csv
Portablehacker: common questions
What microcontroller does the Portablehacker use?
The Portablehacker is built around the ESP32-DEVKITC, from the ESP32 family.
How big is the Portablehacker PCB?
The Portablehacker measures 44.6 × 132.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Portablehacker?
5 components, from 4 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Portablehacker design files?
From the linuskjk/portablehacker repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Portablehacker design in my own project?
Yes, under the terms of its MIT license, which linuskjk chose for the repository.
Can I test firmware for the Portablehacker without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k