Enc v1 a
LiU-SeeGoals·Electronics·enc_v1/enc_v1_a/enc_v1_a.kicad_pcb
About the Enc v1 a PCB
Enc v1 a is an open source STM32 PCB design by LiU-SeeGoals, published on GitHub. It is a 2-layer board measuring 24 × 15.5 mm, with 3 components from 3 distinct parts.
Its main chip is the STM32H755ZITX, from the STM32 family. By type, the board carries 1 IC, 1 connector and 1 capacitor.
From the project
Schematics etc.
Motor driver has 5 pins to the devboard, 2 power pins and 8 pins to the motor
Capacitors and components change capacitance, inductance, etc as the voltage changes. This was not know during the making of driver.
Capacitors should be closer to the pins they are filtering.
There is a risk of overheating if the motors get stuck for a longer time, adding some cooling would be nice.
Main components on the Enc v1 a
Enc v1 a bill of materials (BOM)
3 components, 3 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | STM32H755ZITX AS5047P-ATSM | SOP65P640X120-14N | U1 |
| 1 | Conn_01x09 | MOLEX_530480910 | J2 |
| 1 | 4.7UF 100n | C_0402_1005Metric | C1 |
Enc v1 a design files
The KiCad project lives in the LiU-SeeGoals/Electronics repository on GitHub; these links point at the commit this page was built from.
Enc v1 a: common questions
What microcontroller does the Enc v1 a use?
The Enc v1 a is built around the STM32H755ZITX, from the STM32 family.
How big is the Enc v1 a PCB?
The Enc v1 a measures 24 × 15.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Enc v1 a?
3 components, from 3 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Enc v1 a design files?
From the LiU-SeeGoals/Electronics repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Enc v1 a design in my own project?
The repository has no license, so all rights stay with LiU-SeeGoals. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Enc v1 a without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in Electronics
Kicker Board (Initial design by A Ryll -Tigers)
LiU-SeeGoals
140 × 85.4 mm63 parts2LNo license0Power board
LiU-SeeGoals
166 × 166 mm53 parts4LNo license0STM32
STM32H755ZI breakout board
LiU-SeeGoals
70 × 95 mm38 parts4LNo license0Driver seperate
LiU-SeeGoals
37.9 × 34.2 mm19 parts4LNo license0Motor driver board for pwr v2
LiU-SeeGoals
30.5 × 31 mm16 parts2LNo license0Kicker breakout
LiU-SeeGoals
44 × 37.8 mm14 parts2LNo license0Imu LSM6DSL
LiU-SeeGoals
25.4 × 21 mm9 parts4LNo license0NRF to Nucleo H536ZI connector board
LiU-SeeGoals
60 × 35 mm3 parts2LNo license0STM32
Enc v1 b
LiU-SeeGoals
24 × 15.5 mm3 parts2LNo license0
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k