FullBoard.v2
liubo817·Diplomna-Rabota·Hardware/Boards/V2 - 1 board/FullBoard_V2/FullBoard.v2.kicad_pcb
About the FullBoard.v2 PCB
FullBoard.v2 is an open source ESP32 PCB design by liubo817, published on GitHub. It is a 2-layer board measuring 137.8 × 64.8 mm, with 14 components from 10 distinct parts.
Its main chip is the MODULE_ESP32-DEVKITC, from the ESP32 family. Other key parts include the GY-8511 UV sensor, TEMT6000, DS18B20-air, DS18B20-water and Turbidity sensor. By type, the board carries 7 ICs, 4 connectors, 2 resistors and 1 relay.

Main components on the FullBoard.v2
FullBoard.v2 bill of materials (BOM)
14 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | GY-8511 UV sensor | 5pin_holes | U1 |
| 1 | TEMT6000 | 3pin_holes | U2 |
| 1 | ~ | MODULE_ESP32-DEVKITC | U3 |
| 1 | DS18B20-air | DS18B20_3dmodel | U4 |
| 1 | DS18B20-water | DS18B20_3dmodel | U5 |
| 1 | Turbidity sensor | 3pin_holes | U6 |
| 1 | Water Level | 3pin_holes | U7 |
| 4 | Conn_01x03_Pin | connector_3p | J1, J2, J3, J4 |
| 1 | Relay_SPDT | Relay | K1 |
| 2 | 2.2k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2 |
FullBoard.v2 design files
The KiCad project lives in the liubo817/Diplomna-Rabota repository on GitHub; these links point at the commit this page was built from.
FullBoard.v2: common questions
What microcontroller does the FullBoard.v2 use?
The FullBoard.v2 is built around the MODULE_ESP32-DEVKITC, from the ESP32 family.
How big is the FullBoard.v2 PCB?
The FullBoard.v2 measures 137.8 × 64.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the FullBoard.v2?
14 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the FullBoard.v2 design files?
From the liubo817/Diplomna-Rabota repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the FullBoard.v2 design in my own project?
The repository has no license, so all rights stay with liubo817. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the FullBoard.v2 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Diplomna-Rabota
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k