Liubomir Stanev project
liubo817·Diplomna-Rabota·Hardware/Boards/V2 - 1 board/Liubomir_Stanev_PCB/Liubomir_Stanev_project.kicad_pcb
About the Liubomir Stanev project PCB
Liubomir Stanev project is an open source ESP32 PCB design by liubo817, published on GitHub. It is a 2-layer board measuring 145.5 × 73.5 mm, with 16 components from 11 distinct parts.
Its main chip is the ESP32, from the ESP32 family. Other key parts include the GY-8511 UV sensor, TEMT6000, DS18B20-air, Turbidity sensor and DS18B20-water. By type, the board carries 8 ICs, 6 connectors and 2 resistors.

Main components on the Liubomir Stanev project
Liubomir Stanev project bill of materials (BOM)
16 components, 11 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | GY-8511 UV sensor | 5pin_holes | U1 |
| 1 | TEMT6000 | 3pin_holes | U2 |
| 1 | DS18B20-air | 3pin_holes | U3 |
| 1 | Turbidity sensor | 3pin_holes | U4 |
| 1 | DS18B20-water | 3pin_holes | U5 |
| 1 | Water Level Sensor | 3pin_holes | U6 |
| 1 | ESP32 | MODULE_ESP32-DEVKITC | U7 |
| 1 | Relay module | connector_6p | U8 |
| 4 | Conn_01x03_Pin | connector_3p | J1, J2, J4, J5 |
| 2 | Conn_01x02_Pin | connector_2p | J3, J6 |
| 2 | 2.2k | R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R1, R2 |
Liubomir Stanev project design files
The KiCad project lives in the liubo817/Diplomna-Rabota repository on GitHub; these links point at the commit this page was built from.
Liubomir Stanev project: common questions
What microcontroller does the Liubomir Stanev project use?
The Liubomir Stanev project is built around the ESP32, from the ESP32 family.
How big is the Liubomir Stanev project PCB?
The Liubomir Stanev project measures 145.5 × 73.5 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Liubomir Stanev project?
16 components, from 11 distinct parts. The full bill of materials is listed on this page.
Where can I download the Liubomir Stanev project design files?
From the liubo817/Diplomna-Rabota repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Liubomir Stanev project design in my own project?
The repository has no license, so all rights stay with liubo817. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Liubomir Stanev project without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in Diplomna-Rabota
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k