Gps
louis-bourgault·gps·hardware/gps.kicad_pcb
About the Gps PCB
Gps is an open source ESP32 PCB design by louis-bourgault, published on GitHub. It is a 2-layer board measuring 24 × 40 mm, with 24 components from 17 distinct parts.
Its main chip is the ESP32-C3-WROOM-02, from the ESP32 family. Other key parts include the TP4057 and TPS78330DDCR. By type, the board carries 6 resistors, 5 capacitors, 4 diodes, 3 ICs, 3 connectors and 3 switches.
It belongs with the rf & radio designs in this gallery.
From the project
This project is, first and foremost, a custom devboard made for macondo. It has a esp32-c3 chip on it. A main tenant of its design is to be as power efficient as possible, because of its secondary purpose as a GNSS board. GNSS is not the primary use - the primary use is to have a
This project is, first and foremost, a custom devboard made for macondo. It has a esp32-c3 chip on it. A main tenant of its design is to be as power efficient as possible, because of its secondary purpose as a GNSS board. GNSS is not the primary use - the primary use is to have a functional, simple, and useful devboard for my own purpose. However, it is a likely extention of the project. The idea is that I've put a bunch of pins on the PCB in the right place to connect to a GNSS module, specifically the ATGM336 family, and designed something power efficient enough to run intermittent tracking…

Main components on the Gps
Gps bill of materials (BOM)
24 components, 17 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | TP4057 | SOT-23-6 | U2 |
| 1 | TPS78330DDCR | DDC5_TEX | U3 |
| 1 | ESP32-C3-WROOM-02 | ESP32-C3-WROOM-02 | U5 |
| 1 | USB_C_RECEPTACLE_USB2.0_14P USB_C_Receptacle_USB2.0_14P | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | CONN_01X06_PIN Conn_01x06_Pin | PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | CONN_01X05_PIN Conn_01x05_Pin | PinHeader_1x05_P2.54mm_Vertical | J5 |
| 2 | C431540 SW_SPDT | SW_SPDT_Shouhan_MSK12C02 | SW1, SW4 |
| 1 | C720477 BOOT | SW_Push_SPST_NO_Alps_SKRK | SW5 |
| 2 | SS14 | D_SOD-123 | D2, D3 |
| 2 | LED | LED_0603_1608Metric | D4, D5 |
| 2 | 1u | C_0402_1005Metric | C1, C2 |
| 1 | 10UF 10uf | C_0402_1005Metric | C3 |
| 2 | 100NF 100nf | C_0402_1005Metric | C4, C5 |
| 1 | 2k | R_0402_1005Metric | R1 |
| 2 | 5.1K 5.1k | R_0402_1005Metric | R2, R3 |
| 2 | 10K 10k | R_0402_1005Metric | R4, R8 |
| 1 | 1k | R_0603_1608Metric | R6 |
Gps design files
The KiCad project lives in the louis-bourgault/gps repository on GitHub; these links point at the commit this page was built from.
Gps: common questions
What microcontroller does the Gps use?
The Gps is built around the ESP32-C3-WROOM-02, from the ESP32 family.
How big is the Gps PCB?
The Gps measures 24 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Gps?
24 components, from 17 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Gps design files?
From the louis-bourgault/gps repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Gps design in my own project?
The repository has no license, so all rights stay with louis-bourgault. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Gps without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k