56 open source boards using the TP4057
Real designs built with the TP4057, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Echoplayer
amachronic
52 × 94 mm141 parts6LCERN-OHL-S-2.0279Nordic nRF
PH60
ph-design
285 × 94.6 mm204 parts2LCC-BY-NC-4.0162Bluetooth minidisc
17o2
72.4 × 44.5 mm71 parts4LNo license44EmoeNAP
Floyd-Fish
75 × 36 mm156 parts4LGPL-3.035Nordic nRF
Mdbt micro
siderakb
33 × 17.8 mm29 parts2LMIT18RP2040/RP2350
MuHack-Badge
MrMoDDoM
100 × 100 mm117 parts2LAGPL-3.08ESP32
Bt nes advantage
aaronperkins
78 × 36 mm26 parts2LGPL-3.05RP2040/RP2350
BuhSat v0
Sadteeto
100 × 100 mm32 parts2LMIT4RP2040/RP2350
Tallytime hardware
micro-henry
80 × 50 mm88 parts4LCERN-OHL-S-2.03ESP32
The-Surevival
Rishaan2202
51 × 23 mm72 parts2LNo license3Nordic nRF
Bifrost left
hringdrifi
142.9 × 80.3 mm40 parts2LCERN-OHL-P-2.03ESP32
Plant-Health-Meter
MarkusVLA
136.2 × 25 mm94 parts4LMIT2AVR/Arduino
Salp board
aeiou642
64.8 × 58.7 mm57 parts4LNo license2ESP32
Main board tft
atomic14
34 × 34 mm44 parts2LNo license2RP2040/RP2350
RP2040-Test-MassProduction
zeankundev
100 × 92.2 mm335 parts2LNo license1Nordic nRF
Nrf52840-microstamp xl
cheyao
59.7 × 30.5 mm71 parts4LCERN-OHL-P-2.01ESP32
SmolExG
matthewlai
51 × 33 mm60 parts4LNo license1ESP8266
Endev v1.1
sophiayduan
36 × 70 mm59 parts2LMIT1Nordic nRF
NRF52840-microstamp
cheyao
37 × 25 mm45 parts4LNo license1Jungle buoy
meshmy
41 × 38 mm26 parts2LCERN-OHL-S-2.01RP2040/RP2350
Saturn60
Charading
285 × 94.6 mm305 parts4LNo license0Flinx
ayukmr
252.5 × 68.8 mm119 parts4LMIT0STM32
Tamagotchi thing
afonsus1997
42.5 × 47 mm76 parts4LNo license0ESP32
Survive
PrinceYadav78
54.7 × 23 mm72 parts4LMIT0Nordic nRF
Nrf52840-stamp xl
cyao1234
59.7 × 30.5 mm71 parts4LCERN-OHL-P-2.00ESP32
FlashKa main
DomPka
24 × 16.5 mm68 parts4LGPL-3.00Nordic nRF
Temperature sensors
askiiart
45 × 48 mm66 parts6LNo license0Panel
PHS-SMCS
155 × 71 mm60 parts2LNo license0ESP32
ESP-32-ruler
rapha-tech
38 × 151.9 mm58 parts2LNo license0Nordic nRF
SnapCore-Devboard-Rev1
Magnetile
26.9 × 47.6 mm51 parts4LMIT0ESP32
BlueSlime-C3
wb1016
30 × 30.1 mm48 parts2LMIT0RISC-V
Barsotion-PL1
Barsy-Barsevich
33 × 20 mm47 parts4LMIT0RISC-V
NoodleDriver
mcqn
36 × 70 mm41 parts2LCERN-OHL-S-2.00Powerbank
philipiak123
91 × 108.5 mm27 parts2LNo license0ESP32
Gps
louis-bourgault
24 × 40 mm24 parts2LNo license0RP2040/RP2350
Skibidi album clicker
tobycm
30 × 70 mm23 parts2LMIT0
How designs wire the TP4057
Read from the KiCad layouts of 41 open source designs, one per repository: what each pin of the TP4057 connects to, and the resistors, capacitors and other passives placed on it.
- The PROG pin has a resistor to GND on 35 of 40 designs, most often 2 kΩ (then 1.5 kΩ).
- The VCC pin has a decoupling capacitor on 27 of 40 designs, most often 10 µF (then 4.7 µF).
- The BAT pin is tied to BATT on 31 of 41 designs (a signal on 10).
- The BAT pin has a decoupling capacitor on 24 of 41 designs, most often 10 µF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 88% | — |
| BATpin 3 | Connected to: BATT 76% · a signal 24% |
|
| VCCpin 4 | Connected to: VBUS 78% · a signal 23% |
|
| PROGpin 6 | Connected to: Signal 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Echoplayer by amachronic, ErgoSNM Keyboard Left Prototype 1 by siderakb, PH60 by ph-design and Bluetooth minidisc by 17o2.
The TP4057 in open source designs
The gallery holds 56 open source boards using the TP4057 from 41 GitHub repositories; a typical one measures about 51 × 47.8 mm and carries around 60 components.
54% use four copper layers or more, and 46% carry an open source license.
The most starred is Echoplayer by amachronic.
Parts used alongside the TP4057
Microcontrollers on boards using the TP4057
What boards using the TP4057 are built for
TP4057: common questions
Where can I find a TP4057 reference design?
Each of the 56 boards on this page is a real design using the TP4057. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TP4057 PROG pin?
The PROG pin has a resistor to GND on 35 of 40 designs, most often 2 kΩ (then 1.5 kΩ). Counted from the KiCad layouts of 41 open source designs using the TP4057.
What decoupling capacitors do designs use on the TP4057 VCC pin?
The VCC pin has a decoupling capacitor on 27 of 40 designs, most often 10 µF (then 4.7 µF). Counted from the KiCad layouts of 41 open source designs using the TP4057.
How is the TP4057 BAT pin connected?
The BAT pin is tied to BATT on 31 of 41 designs (a signal on 10). Counted from the KiCad layouts of 41 open source designs using the TP4057.
What parts are used alongside the TP4057?
The nRF52840, RP2040, SRV05-4, USBLC6-2SC6 and DW01A appear in the most repositories here.
Which microcontrollers do boards using the TP4057 use?
Most are built on ESP32 (18), Nordic nRF (12), RP2040/RP2350 (11) and STM32 (2).
How big is a typical board using the TP4057?
The median is 51 × 47.8 mm, and 46% are two-layer designs.
What is the most popular open source board using the TP4057?
By GitHub stars, Echoplayer by amachronic, with 279 stars.
Can I simulate one of these boards using the TP4057 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.