CO2-Ampel mit D1 mini
LouisNikolaus·GFS---CO2-Ampel·Platine/CO2-Ampel.kicad_pcb
About the CO2-Ampel mit D1 mini PCB
CO2-Ampel mit D1 mini is an open source ESP8266 PCB design by LouisNikolaus, published on GitHub. It is a 2-layer board measuring 100 × 60 mm, with 17 components from 14 distinct parts.
Its main chip is the D1 mini (ESP8266), from the ESP8266 family. By type, the board carries 6 resistors, 4 diodes, 2 connectors, 1 IC, 1 transistor and 1 buzzer.
It belongs with the sensors and displays & leds designs in this gallery.
From the project
Trägerplatine 100 × 60 mm (2 Lagen, nur THT-Bauteile) + 3D-gedrucktes Gehäuse 105 × 65 × 27 mm.
Trägerplatine 100 × 60 mm (2 Lagen, nur THT-Bauteile) + 3D-gedrucktes Gehäuse 105 × 65 × 27 mm.
- 2 × Buchsenleiste 1×8, RM 2,54 (für den D1 mini) - 4 × Schraube M3 × 8 (Platine auf Abstandshalter, selbstschneidend) - Aktiver Summer 5 V, 12 mm, Rastermaß 7,6 mm - Taster 6 × 6 mm mit 13 mm Bauhöhe
1. Pinfolge des CO2-Sensors: J2 ist VCC–GND–SCL–SDA belegt. Das Sensormodul (SCD40/SCD41/SCD30 …) vergleichen. 2. Pinfolge des OLED: J1 ist GND–VCC–SCL–SDA belegt. Manche Displays haben VCC–GND! 3. JP1 (Lötbrücke): ab Werk 3,3 V für den Sensor. Für 5 V die Brücke 1-2 auftrennen und 2-3 verbinden.…
Main components on the CO2-Ampel mit D1 mini
CO2-Ampel mit D1 mini bill of materials (BOM)
17 components, 14 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | D1 mini (ESP8266) | WEMOS_D1_mini | U1 |
| 1 | BC547 | TO-92_Inline | Q1 |
| 1 | OLED 0,96" SSD1306 | PinSocket_1x04_P2.54mm_Vertical | J1 |
| 1 | CO2-Sensor I2C | PinSocket_1x04_P2.54mm_Vertical | J2 |
| 1 | Summer 5V aktiv | Buzzer_12x9.5RM7.6 | BZ1 |
| 1 | Taster | SW_PUSH_6mm_H13mm | SW1 |
| 1 | LED 5mm rot | LED_D5.0mm | D1 |
| 1 | LED 5mm gelb | LED_D5.0mm | D2 |
| 1 | LED 5mm gruen | LED_D5.0mm | D3 |
| 1 | 1N4148 | D_DO-35_SOD27_P7.62mm_Horizontal | D4 |
| 1 | 100UF 100uF | CP_Radial_D6.3mm_P2.50mm | C1 |
| 2 | 4k7 (opt.) | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2 |
| 3 | 220 | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R4, R5 |
| 1 | 1k | R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R6 |
CO2-Ampel mit D1 mini design files
The KiCad project lives in the LouisNikolaus/GFS---CO2-Ampel repository on GitHub; these links point at the commit this page was built from.
CO2-Ampel mit D1 mini: common questions
What microcontroller does the CO2-Ampel mit D1 mini use?
The CO2-Ampel mit D1 mini is built around the D1 mini (ESP8266), from the ESP8266 family.
How big is the CO2-Ampel mit D1 mini PCB?
The CO2-Ampel mit D1 mini measures 100 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the CO2-Ampel mit D1 mini?
17 components, from 14 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the CO2-Ampel mit D1 mini design files?
From the LouisNikolaus/GFS---CO2-Ampel repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the CO2-Ampel mit D1 mini design in my own project?
The repository has no license, so all rights stay with LouisNikolaus. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the CO2-Ampel mit D1 mini without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
More boards in GFS---CO2-Ampel
Similar boards
ESP8266
ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1kESP8266
HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738ESP8266
RatGDO-OpenSource-Bare-ESP8266
Kaldek
55 × 82.7 mm20 parts2LMIT506ESP8266
Goatgdo
Kaldek
32.9 × 53.3 mm23 parts2LMIT506ESP8266
RatGDO-OpenSource-D1Mini-ESP8266
Kaldek
47.8 × 63.3 mm12 parts2LMIT506ESP8266
Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398