Main jig
mackieks·fujiflex·KiCAD/factory_jigs/main_jig/main_jig.kicad_pcb
About the Main jig PCB
Main jig is an open source FPGA PCB design by mackieks, published on GitHub under the SHL-2.1 license. It is a 2-layer board measuring 51.3 × 48.2 mm, with 21 components from 11 distinct parts.
Its main chip is the XC3S200A-4VQG100C, from the FPGA family. Other key parts include the LW5912N23D and P25Q40H-UXH-IR. By type, the board carries 9 capacitors, 5 resistors, 3 ICs, 2 connectors, 1 crystal and 1 switch.
From the project
GCVideo DVI flex PCB for Nintendo Wii
OSHW GCVideo DVI flex for Nintendo Wii. Tested and working! Solderpad Hardware License v2.1
Special thanks to loopj for testing the FPC and writing the assembly+install documentation!
I maintain a Mouser project with most of the BOM. You still need to source the FPGA from elsewhere. I suggest either LCSC, AliExpress, or Taobao.
The total BOM cost for fujiflex is around 10USD. If you're paying more than $5 per FPGA, you are being ripped off!

Main components on the Main jig
Main jig bill of materials (BOM)
21 components, 11 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LW5912N23D SPX3819M5-L-3-3/TR Lewa Micro | SOT-23-5 | U1 |
| 1 | XC3S200A-4VQG100C SPX3819M5-L-1-8/TR Xilinx / AMD | SOT-23-5 | U2 |
| 1 | P25Q40H-UXH-IR CH347T PUYA | TSSOP-20_L6.5-W4.4-P0.65-LS6.4-BL | U3 |
| 1 | 8MHz | Crystal_SMD_5032-2Pin_5.0x3.2mm | Y1 |
| 1 | 505278-1933 217179-0001 Molex | USB-C_SMD-TYPE-C-31-M-12 | J1 |
| 1 | Conn_01x21_Pin | FPC-SMD_19P-P0.50_AFD01-S19FCA-00 | J2 |
| 1 | KH-6X6X6H-STM | SW-SMD_4P-L6.0-W6.0-P4.50-LS9.0-3 | SW1 |
| 5 | 1µF | C_0402_1005Metric | C1, C2, C3, C4, C7 |
| 2 | 0.1µF | C_0402_1005Metric | C5, C6 |
| 2 | 22pF | C_0402_1005Metric | C8, C9 |
| 5 | 5.1k | R_0402_1005Metric | R1, R2, R3, R4, R5 |
Main jig design files
The KiCad project lives in the mackieks/fujiflex repository on GitHub; these links point at the commit this page was built from.
Main jig: common questions
What microcontroller does the Main jig use?
The Main jig is built around the XC3S200A-4VQG100C, from the FPGA family.
How big is the Main jig PCB?
The Main jig measures 51.3 × 48.2 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Main jig?
21 components, from 11 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Main jig design files?
From the mackieks/fujiflex repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Main jig design in my own project?
It is published under SHL-2.1, which limits how it may be reused; read the license before building on it.
Can I test firmware for the Main jig without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.
More boards in fujiflex
Similar boards
FPGA
Base board
GlasgowEmbedded
80 × 49 mm222 parts4L0BSD2.2kFPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kFPGA
Usb sniffer
ataradov
58.2 × 38.1 mm86 parts2LBSD-3-Clause1.3kFPGA
Tomu, I'm
theacodes
13 × 9.4 mm40 parts4LMIT1.1kFPGA
Icepi zero
cheyao
65 × 30 mm143 parts4LSHL-2.1865FPGA
Gcvideo
ikorb
49 × 30 mm44 parts4LNo license765