Makers motor board
Makers-Oakland-University·makers-motor-board·KiCad Files/makers-motor-board.kicad_pcb
About the Makers motor board
Makers motor board is an open source ESP32 PCB design by Makers-Oakland-University, published on GitHub. It is a 2-layer board measuring 58 × 76.8 mm, with 13 components from 7 distinct parts.
Its main chip is the ESP32_DevKit_V1_DOIT, from the ESP32 family. Other key parts include the LM7805_TO220 and L293D. By type, the board carries 8 connectors, 3 ICs and 2 capacitors.
It belongs with the robotics & motion and iot & wireless designs in this gallery.
From the project
a general motor control board for small robots
The Makers @ OU motor board is meant to serve as a general-purpose robot base for all kinds of projects. The board utilizes the ESP32 Devkit 1, along with an L293D H-Bridge driver. The LM7805 voltage regulator enables the board to be powered from any supply between 4.5V and 30V. The input voltage can be used directly to drive the motor, or the 5V power rail can be used through selection through the header.

Main components on the Makers motor board
Makers motor board bill of materials (BOM)
13 components, 7 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM7805_TO220 | TO-220-3_Horizontal_TabDown | U1 |
| 1 | ESP32_DevKit_V1_DOIT | esp32_devkit_v1_doit | U2 |
| 1 | L293D | DIP-16_W7.62mm | U3 |
| 4 | Screw_Terminal_01x02 | terminal_block_5mm | J1, J2, J5, J6 |
| 2 | Conn_01x15_Female | PinSocket_1x15_P2.54mm_Vertical | J3, J4 |
| 2 | Conn_01x02_Male | PinHeader_1x02_P2.54mm_Vertical | J7, J8 |
| 2 | C_Polarized_US | CP_Radial_D8.0mm_P3.50mm | C1, C2 |
Makers motor board design files
The KiCad project lives in the Makers-Oakland-University/makers-motor-board repository on GitHub; these links point at the commit this page was built from.
Makers motor board: common questions
What microcontroller does the Makers motor board use?
The Makers motor board is built around the ESP32_DevKit_V1_DOIT, from the ESP32 family.
How big is the Makers motor board?
The Makers motor board measures 58 × 76.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Makers motor board?
13 components, from 7 distinct parts. The full bill of materials is listed on this page.
Where can I download the Makers motor board design files?
From the Makers-Oakland-University/makers-motor-board repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Makers motor board design in my own project?
The repository has no license, so all rights stay with Makers-Oakland-University. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Makers motor board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k