LibreHealth-Lift
About the LibreHealth-Lift PCB
LibreHealth-Lift is an open source ESP32 PCB design by Mallo321123, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 97 × 67 mm, with 18 components from 12 distinct parts.
Its main chip is the ESP32-S3-DevKitC, from the ESP32 family. Other key parts include the SD card. By type, the board carries 7 connectors, 3 ICs, 3 transistors, 3 jumpers, 1 capacitor and 1 resistor.
From the project
PCB/Electronic Files for LibreHealth-Lift
Main components on the LibreHealth-Lift
LibreHealth-Lift bill of materials (BOM)
18 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DevKitC | ESP32-S3-DevKitC | U1 |
| 1 | ~ | ISM330DLC | U2 |
| 1 | SD card | SD-Breakout | U3 |
| 3 | PMOS | TSOT-23 | Q1, Q2, Q3 |
| 3 | SPI | PinHeader_1x04_P2.54mm_Vertical | J1, J3, J4 |
| 1 | SPI-CS | PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | 3.3V | PinHeader_1x04_P2.54mm_Vertical | J5 |
| 1 | GND | PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | Display | PinHeader_1x04_P2.54mm_Vertical | J7 |
| 3 | Jumper_2_Bridged | Jumper_P2.54mm_D1.2mm | JP1, JP2, JP3 |
| 1 | C_Polarized | CP_Radial_D8.0mm_P3.80mm | C1 |
| 1 | 22R | R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
LibreHealth-Lift design files
The KiCad project lives in the Mallo321123/LibreHealth-Lift_PCB repository on GitHub; these links point at the commit this page was built from.
LibreHealth-Lift: common questions
What microcontroller does the LibreHealth-Lift use?
The LibreHealth-Lift is built around the ESP32-S3-DevKitC, from the ESP32 family.
How big is the LibreHealth-Lift PCB?
The LibreHealth-Lift measures 97 × 67 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the LibreHealth-Lift?
18 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the LibreHealth-Lift design files?
From the Mallo321123/LibreHealth-Lift_PCB repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the LibreHealth-Lift design in my own project?
Yes, under the terms of its GPL-3.0 license, which Mallo321123 chose for the repository.
Can I test firmware for the LibreHealth-Lift without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1k
ESP32Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0k
ESP32Esp32 minimal
36.2 × 26.8 mm20 parts2LMIT4.0k
ESP32Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k
ESP32Controller
29 × 74 mm58 parts4LApache-2.03.8k
ESP32Bitaxe
skot
56.5 × 99.8 mm86 parts4LCERN-OHL-S-2.01.4k