8 open source boards using the SD_CARD
Real designs built with the SD_CARD, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
LPA-hardware
taborlab
143 × 74 mm81 parts2LNo license11FPGA
CORE
Han-ZenX
118 × 97 mm81 parts4LCustom license1AVR/Arduino
Ofen v2
Ulf-vom-Mond
109.2 × 63.5 mm58 parts2LNo license1PIC
PTR arecorder
PTR-projects
74 × 25 mm83 parts2LMIT0AVR/Arduino
LPA-FW
TheEngineeringOctopus
143 × 74 mm81 parts2LNo license0Slimmy
devisunofficial
41 × 21 mm24 parts4LNo license0ESP32
LibreHealth-Lift
Mallo321123
97 × 67 mm18 parts2LGPL-3.00AVR/Arduino
RainGauge
ARTS-Laboratory
64 × 40.5 mm14 parts2LCC-BY-SA-4.00
How designs wire the SD_CARD
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the SD_CARD connects to, and the resistors, capacitors and other passives placed on it.
- The CD/SW_9 pin is left unconnected on 3 of 4 designs.
- The CD_CD pin is left unconnected on 2 of 3 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDD_4pin 4 | Connected to: VCC 63% · a signal 38% | — |
| VSS_6pin 6 | Connected to: GND 71% · a signal 29% | — |
| CD/SW_9pin 9 | Connected to: Not connected 75% · a signal 25% | — |
| CD_CDpin CD | Connected to: Not connected 67% · a signal 33% | — |
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include LPA-hardware by taborlab, CORE by Han-ZenX, Ofen v2 by Ulf-vom-Mond and RainGauge PCB by ARTS-Laboratory.
The SD_CARD in open source designs
The gallery holds 8 open source boards using the SD_CARD from 8 GitHub repositories; a typical one measures about 103.1 × 65.3 mm and carries around 70 components.
75% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is LPA-hardware by taborlab.
Parts used alongside the SD_CARD
Microcontrollers on boards using the SD_CARD
What boards using the SD_CARD are built for
SD_CARD: common questions
Where can I find a SD_CARD reference design?
Each of the 8 boards on this page is a real design using the SD_CARD. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the SD_CARD CD/SW_9 pin connected?
The CD/SW_9 pin is left unconnected on 3 of 4 designs. Counted from the KiCad layouts of 8 open source designs using the SD_CARD.
How is the SD_CARD CD_CD pin connected?
The CD_CD pin is left unconnected on 2 of 3 designs. Counted from the KiCad layouts of 8 open source designs using the SD_CARD.
What parts are used alongside the SD_CARD?
The AP1509, ATMEGA328-A and TLC5941 appear in the most repositories here.
Which microcontrollers do boards using the SD_CARD use?
Most are built on AVR/Arduino (4), ESP32 (1), FPGA (1) and PIC (1).
How big is a typical board using the SD_CARD?
The median is 103.1 × 65.3 mm, and 75% are two-layer designs.
What is the most popular open source board using the SD_CARD?
By GitHub stars, LPA-hardware by taborlab, with 11 stars.
Can I simulate one of these boards using the SD_CARD before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.