EE-Onboarding-Macallan
marocco-ui·EE-Onboarding-Macallan
About the EE-Onboarding-Macallan PCB
EE-Onboarding-Macallan is an open source ESP32 PCB design by marocco-ui, published on GitHub. It is a 2-layer board measuring 60 × 60 mm, with 25 components from 18 distinct parts.
Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the AP7361C-33E-13. By type, the board carries 9 resistors, 8 capacitors, 3 switches, 2 ICs, 2 connectors and 1 diode.
It belongs with the iot & wireless designs in this gallery.
From the project
Macallan Rocco's ESP32 PCB design project
EE subteam onboarding project. A 2-layer, 60 × 60 mm board that reads one 0 to 3.3 V analog sensor and one pushbutton with an ESP32-S3, powered and programmed over USB-C.
Calculations for the regulator, LED resistor, power budget, and trace widths are in calculations.md.
USB-C (J1) --5 V--> AP7361C LDO (U2) --3.3 V--> ESP32-S3-WROOM-1 (U1) | | +---- D+ / D- (native USB) ---------------------+ | Sensor connector (J2) --> divider + RC filter --> GPIO1 (ADC1_CH0) User button (SW1) --> pull-up + RC debounce --> GPIO4 BOOT (SW2) --> GPIO0 RESET (SW3) --> EN

Main components on the EE-Onboarding-Macallan
EE-Onboarding-Macallan bill of materials (BOM)
25 components, 18 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1-N8 | ESP32-S3-WROOM-1 | U1 |
| 1 | AP7361C-33E-13 | SOT-223-3_TabPin2 | U2 |
| 1 | GCT USB4105-GF-A USB_C_USB2.0 | USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | SENSOR | JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | J2 |
| 1 | USER | SW_SPST_TL3342 | SW1 |
| 1 | BOOT | SW_SPST_TL3342 | SW2 |
| 1 | RESET | SW_SPST_TL3342 | SW3 |
| 1 | LTST-C191KGKT | LED_0603_1608Metric | D1 |
| 1 | 4.7uF 10V | C_0805_2012Metric | C1 |
| 4 | 100nF | C_0603_1608Metric | C2, C5, C7, C8 |
| 1 | 10uF 10V | C_0805_2012Metric | C3 |
| 1 | 22uF 10V | C_0805_2012Metric | C4 |
| 1 | 1uF | C_0603_1608Metric | C6 |
| 4 | 10k | R_0603_1608Metric | R1, R2, R3, R7 |
| 1 | 680 | R_0603_1608Metric | R4 |
| 1 | 10k 1% | R_0603_1608Metric | R5 |
| 1 | 30k 1% | R_0603_1608Metric | R6 |
| 2 | 5.1k | R_0603_1608Metric | R8, R9 |
EE-Onboarding-Macallan design files
The KiCad project lives in the marocco-ui/EE-Onboarding-Macallan repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad bike project.kicad_pcb
- Schematickicad bike project.kicad_sch
EE-Onboarding-Macallan: common questions
What microcontroller does the EE-Onboarding-Macallan use?
The EE-Onboarding-Macallan is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.
How big is the EE-Onboarding-Macallan PCB?
The EE-Onboarding-Macallan measures 60 × 60 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the EE-Onboarding-Macallan?
25 components, from 18 distinct parts. The full bill of materials is listed on this page.
Where can I download the EE-Onboarding-Macallan design files?
From the marocco-ui/EE-Onboarding-Macallan repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the EE-Onboarding-Macallan design in my own project?
The repository has no license, so all rights stay with marocco-ui. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the EE-Onboarding-Macallan without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k