Electrotrack
maslohaslo1234-spec·electrotrack·hardware/electrotrack.kicad_pcb
About the Electrotrack PCB
Electrotrack is an open source ESP32 PCB design by maslohaslo1234-spec, published on GitHub under the MIT license. It is a 2-layer board measuring 100 × 83.5 mm, with 44 components from 20 distinct parts.
Its main chip is the ESP32_30pin, from the ESP32 family. Other key parts include the L7805. By type, the board carries 16 resistors, 11 connectors, 5 diodes, 4 transistors, 4 capacitors and 2 ICs.
It belongs with the displays & leds and sensors designs in this gallery.
From the project
A PCB for a metal ball track that will be accelerated with electromagnets. More details will be added later as the project develops
Electrotrack is an experimental multi-stage electromagnetic ball accelerator (coilgun). An ESP32 reads infrared (IR) photo-interrupter sensors placed along a 3D-printed track and fires a sequence of coils to pull a steel ball forward. Each coil is switched off as the ball reaches its centre, so the ball is not pulled back.
- Controller: ESP32 30-pin development board, plugged into the PCB. - Coil drivers: 4 channels, each with a logic-level N-channel MOSFET (IRLZ44N), a gate series resistor and pull-down, and an SB560 flyback diode. Coils connect to screw terminals. - Position sensing: 4 IR…
Main components on the Electrotrack
Electrotrack bill of materials (BOM)
44 components, 20 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ~ | ESP32_30pin | U1 |
| 1 | L7805 | TO-220-3_Vertical | U2 |
| 4 | IRLZ44N | TO-220-3_Vertical | Q1, Q2, Q3, Q4 |
| 4 | IR | JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J1, J2, J3, J4 |
| 1 | XT30 | AMASS_XT30UPB-M_1x02_P5.0mm_Vertical | J5 |
| 4 | Coil | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J6, J7, J8, J9 |
| 1 | 0.96 inch OLED | PinSocket_1x04_P2.54mm_Vertical | J10 |
| 1 | CONN_01X10_PIN Conn_01x10_Pin | PinSocket_1x10_P2.54mm_Vertical | J11 |
| 1 | 5A fast | Fuseholder_Clip-5x20mm_Littelfuse_520_Inline_P20.50x5.80mm_D1.30mm_Horizontal | F1 |
| 1 | SW_SPST | TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | SW1 |
| 4 | SB560 | D_DO-201AD_P15.24mm_Horizontal | D1, D2, D3, D4 |
| 1 | 1N5819 | D_DO-41_SOD81_P10.16mm_Horizontal | D5 |
| 1 | electrolitic 1000μF | CP_Radial_D10.0mm_P5.00mm | C1 |
| 1 | C 100nF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C2 |
| 1 | 100 µF | CP_Radial_D6.3mm_P2.50mm | C3 |
| 1 | 100NF 100nF | C_Disc_D5.0mm_W2.5mm_P5.00mm | C4 |
| 4 | 10k Ω | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2, R3, R4 |
| 4 | 150Ω | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5, R6, R7, R8 |
| 4 | 100Ω | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R9, R10, R11, R12 |
| 4 | 10kΩ | R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R13, R14, R15, R16 |
Electrotrack design files
The KiCad project lives in the maslohaslo1234-spec/electrotrack repository on GitHub; these links point at the commit this page was built from.
Electrotrack: common questions
What microcontroller does the Electrotrack use?
The Electrotrack is built around the ESP32_30pin, from the ESP32 family.
How big is the Electrotrack PCB?
The Electrotrack measures 100 × 83.5 mm, has 2 copper layers and is 1.600198 mm thick.
How many components are on the Electrotrack?
44 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Electrotrack design files?
From the maslohaslo1234-spec/electrotrack repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Electrotrack design in my own project?
Yes, under the terms of its MIT license, which maslohaslo1234-spec chose for the repository.
Can I test firmware for the Electrotrack without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k