HardLabs

Rilis1

mekatronik-achmadi·openpv·rilis1-pcb/rilis1.kicad_pcb

Rilis1 PCB layout, top view — open source AVR/Arduino board by mekatronik-achmadi

About the Rilis1 PCB

Rilis1 is an open source AVR/Arduino PCB design by mekatronik-achmadi, published on GitHub. It is a 2-layer board measuring 115.1 × 61 mm, with 60 components from 22 distinct parts.

Its main chip is the ATMEGA8A-A, from the AVR/Arduino family. Other key parts include the LM2596S-5v, LM2596S-12v, LM2596S-Adj and STEREOJACK_STX3100. By type, the board carries 18 diodes, 11 resistors, 10 capacitors, 9 ICs, 4 inductors and 3 connectors.

Main components on the Rilis1

ATMEGA8A-ALM2596S-5vLM2596S-12vLM2596S-AdjSTEREOJACK_STX3100

Rilis1 bill of materials (BOM)

60 components, 22 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ATMEGA8A-A
IC1
2
LM2596S-5v
IC-Reg1, IC-Reg2
1
LM2596S-12v
IC-Reg3
1
LM2596S-Adj
IC-Reg4
4
STEREOJACK_STX3100
U1, U2, U3, U4
1
BARREL_JACK
CON1
1
USB_A
P1
1
CONN_01X02
P-VCC1
1
CONN_01X06
ASP1
1
5v6
DZ-USB1
1
5v1
DZ-VCC1
1
10-XX
S-RST1
1
CONN_01X04
UART1
6
LED
D1, D2, D3, D4, D5, D6
7
D_Schottky
D-ADC-LAMP1, D-ADC-USB1, D-Scot1, D-Scot2, D-Scot3, D-Scot4, D-VCC1
5
D
D-Reg1, D-Reg2, D-Reg3, D-Reg4, D-V12
4
INDUCTOR
L-Reg1, L-Reg2, L-Reg3, L-Reg4
2
C
C-BATT1, C-PVS1
8
CP
C-RegA1, C-RegA2, C-RegA3, C-RegA4, C-RegB1, C-RegB2, C-RegB3, C-RegB4
4
R
R-BATT1, R-BATT2, R-PVS1, R-PVS2
Show 2 more
QtyPartRefs
4
4k7
R-CONN1, R-CONN2, R-CONN3, R-RST1
3
330
R-LEDIND-1, R-LEDIND-2, R-LEDIND-3

Rilis1 design files

The KiCad project lives in the mekatronik-achmadi/openpv repository on GitHub; these links point at the commit this page was built from.

Rilis1: common questions

What microcontroller does the Rilis1 use?

The Rilis1 is built around the ATMEGA8A-A, from the AVR/Arduino family.

How big is the Rilis1 PCB?

The Rilis1 measures 115.1 × 61 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rilis1?

60 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Rilis1 design files?

From the mekatronik-achmadi/openpv repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Rilis1 design in my own project?

The repository has no license, so all rights stay with mekatronik-achmadi. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Rilis1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.

More boards in openpv

Similar boards