12 open source boards using the ATmega8A-A
Real designs built with the ATmega8A-A, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
NoahESC
zosko
32 × 43.7 mm48 parts2LNo license3AVR/Arduino
Kombo nrf24 atmega8
MelexinVN
37.6 × 30.7 mm24 parts2LGPL-3.03AVR/Arduino
Maison JP DJ
Antoine-GG
96.9 × 99.9 mm100 parts4LNo license0AVR/Arduino
Rilis1
mekatronik-achmadi
115.1 × 61 mm60 parts2LNo license0AVR/Arduino
AlarmClock
GHOST-mHBr
69.8 × 50 mm36 parts2LNo license0AVR/Arduino
ATMega8 Minimum System
mekatronik-achmadi
28.9 × 35.4 mm22 parts2LNo license0AVR/Arduino
ModuleController
dennis9819
68.3 × 90 mm20 parts2LAGPL-3.00AVR/Arduino
ESC atmega8
fademike
23 × 23 mm51 parts2LNo license1AVR/Arduino
ModuleController old
dennis9819
68.3 × 90 mm20 parts2LAGPL-3.00AVR/Arduino
USBAsp
mekatronik-achmadi
29.6 × 33.6 mm20 parts2LNo license0AVR/Arduino
Kombo nrf24 atmega8 min
MelexinVN
15.9 × 29.6 mm20 parts2LGPL-3.03AVR/Arduino
Generic USBAsp
mekatronik-achmadi
47.3 × 25 mm23 parts2LNo license2
How designs wire the ATmega8A-A
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the ATmega8A-A connects to, and the resistors, capacitors and other passives placed on it.
- The PB6/XTAL1 pin has a crystal on 6 of 9 designs, most often 16 MHz (then 12 MHz).
- The PB7/XTAL2 pin has a crystal on 6 of 9 designs, most often 16 MHz (then 12 MHz).
- The AVCC pin has a decoupling capacitor on 6 of 9 designs, most often 100 nF (then 10 µF).
- The ADC6 pin is left unconnected on 7 of 9 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 3, 5 | Connected to: GND 89% | — |
| VCCpin 4, 6 | Connected to: 5V 89% | — |
| PB6/XTAL1pin 7 | Connected to: Signal 89% |
|
| PB7/XTAL2pin 8 | Connected to: Signal 89% |
|
| PD5pin 9 | Connected to: Signal 67% · not connected 33% |
|
| PD6pin 10 | Connected to: A connector 22% · not connected 22% |
|
| PD7pin 11 | Connected to: A connector 22% · not connected 22% |
|
| PB0pin 12 | Connected to: A connector 22% · not connected 22% |
|
| PB1pin 13 | Connected to: Signal 56% · not connected 44% |
|
| PB2pin 14 | Connected to: A connector 22% · not connected 33% |
|
| AVCCpin 18 | Connected to: VCC 78% · a signal 22% |
|
| ADC6pin 19 | Connected to: Not connected 78% · a signal 22% | — |
| AREFpin 20 | Connected to: Not connected 33% · VCC 33% · a signal 33% |
|
| AGNDpin 21 | Connected to: GND 89% | — |
| PC6/RESETpin 29 | Connected to: A connector 56% |
|
| PD0pin 30 | Connected to: Signal 78% · not connected 22% |
|
| PD1pin 31 | Connected to: Signal 78% · not connected 22% |
|
| PD2pin 32 | Connected to: Signal 89% |
|
12 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Kombo nrf24 atmega8 by MelexinVN, NoahESC by zosko, Generic USBAsp by mekatronik-achmadi and ESC atmega8 by fademike.
The ATmega8A-A in open source designs
The gallery holds 12 open source boards using the ATmega8A-A from 9 GitHub repositories; a typical one measures about 42.4 × 39.5 mm and carries around 24 components.
92% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is NoahESC by zosko.
Microcontrollers on boards using the ATmega8A-A
What boards using the ATmega8A-A are built for
ATmega8A-A: common questions
Where can I find a ATmega8A-A reference design?
Each of the 12 boards on this page is a real design using the ATmega8A-A. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ATmega8A-A PB6/XTAL1 pin connected?
The PB6/XTAL1 pin has a crystal on 6 of 9 designs, most often 16 MHz (then 12 MHz). Counted from the KiCad layouts of 9 open source designs using the ATmega8A-A.
How is the ATmega8A-A PB7/XTAL2 pin connected?
The PB7/XTAL2 pin has a crystal on 6 of 9 designs, most often 16 MHz (then 12 MHz). Counted from the KiCad layouts of 9 open source designs using the ATmega8A-A.
What decoupling capacitors do designs use on the ATmega8A-A AVCC pin?
The AVCC pin has a decoupling capacitor on 6 of 9 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 9 open source designs using the ATmega8A-A.
Which microcontrollers do boards using the ATmega8A-A use?
Most are built on AVR/Arduino (12).
How big is a typical board using the ATmega8A-A?
The median is 42.4 × 39.5 mm, and 92% are two-layer designs.
What is the most popular open source board using the ATmega8A-A?
By GitHub stars, NoahESC by zosko, with 3 stars.
Can I simulate one of these boards using the ATmega8A-A before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.