VoxLink - Shell Module - Daisy
About the VoxLink - Shell Module - Daisy
VoxLink - Shell Module - Daisy is an open source PCB design by MichalVarsanyi, published on GitHub under the MIT license. It is a 4-layer board measuring 54 × 29.5 mm, with 9 components from 9 distinct parts.
Other key parts include the VoxLink_Core_Module and VoxLink_BNO086_Module. By type, the board carries 2 ICs, 2 connectors, 2 capacitors, 2 resistors and 1 switch.
It belongs with the sensors designs in this gallery.
From the project
VoxLink is a high-speed solution that allows interfacing of up to 100 sensors using a single high-speed host device. The communication protocol is agnostic to the sensor board, freeing the user from handling low-level communication. This project is part of my Bachelor's thesis at the Czech Technical University in Prague.
- During programming, exceeding internal clocking speeds of 100MHz on the iCE40UL1K-CM36AI FPGA proved to be virtually impossible. In the future, instantiating the hard IP I2C blocks in the FPGA silicon may increase the speed. Realistically, however, switching to a higher speed grade of FPGAs will probably be the best option.
It may seem that 50-100 MHz is unreasonably fast; however, just 40 sensors at 9 kHz get very close to this ballpark. It is difficult to determine what may increase the bandwidth in the future, so it's better to have an excess than to have too little bandwidth.…
Main components on the VoxLink - Shell Module - Daisy
VoxLink - Shell Module - Daisy bill of materials (BOM)
9 components, 9 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | VoxLink_Core_Module | VoxLink_Core_Module | U1 |
| 1 | VoxLink_BNO086_Module | VoxLink_BNO086_Module | U2 |
| 1 | PicoBlade | Molex_PicoBlade_53048-0810_1x08_P1.25mm_Horizontal | J1 |
| 1 | RJ45_Output | CONN_855035-101_MOL | J2 |
| 1 | Reset | SW_TH_Tactile_Omron_B3F-102x | SW301 |
| 1 | 10u | C_1206_3216Metric | C1 |
| 1 | 10U 1u Murata | C_0805_2012Metric | C304 |
| 1 | 1R | R_0603_1608Metric | R1 |
| 1 | 10k | R_0603_1608Metric | R2 |
VoxLink - Shell Module - Daisy design files
The KiCad project lives in the MichalVarsanyi/VoxLink repository on GitHub; these links point at the commit this page was built from.
VoxLink - Shell Module - Daisy: common questions
How big is the VoxLink - Shell Module - Daisy?
The VoxLink - Shell Module - Daisy measures 54 × 29.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the VoxLink - Shell Module - Daisy?
9 components, from 9 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the VoxLink - Shell Module - Daisy design files?
From the MichalVarsanyi/VoxLink repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the VoxLink - Shell Module - Daisy design in my own project?
Yes, under the terms of its MIT license, which MichalVarsanyi chose for the repository.
More boards in VoxLink
FPGAController Board
85 × 85 mm291 parts6LMIT1
FPGAProgrammer Sensor Stencil
85 × 15.8 mm118 parts2LMIT1
FPGAVoxSense Sensor Board
85 × 15.8 mm92 parts4LMIT1
VoxLink Programmer Board
49.1 × 15.5 mm55 parts4LMIT1
FPGAVoxLink - Lattice Core Module
13 × 13 mm52 parts6LMIT1
VoxLink - BNO086 Sensor Module
13 × 13 mm32 parts4LMIT1
FPGACore Module Intel
13 × 13 mm27 parts6LMIT1
VoxLink Programmer Shell
70 × 70 mm7 parts4LMIT1
VoxLink - Shell Module Bus
54 × 29.5 mm4 parts4LMIT1
Similar boards
Sensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8k
Microphone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2k
TemperaturePCB PANEL
stuartpittaway
116 × 75.5 mm178 parts2LCC-BY-NC-4.01.1k
FourThirdsEye
will127534
47 × 47 mm106 parts4LMIT377
VESC Controller
paltatech
160 × 90 mm908 parts2LNo license354
OneInchEye
39 × 39 mm79 parts4LMIT346