Esp32-iot base
mightea·esp32-iot-base·pcb/iotbase.kicad_pcb
About the Esp32-iot base PCB
Esp32-iot base is an open source ESP32 PCB design by mightea, published on GitHub under the CERN-OHL-1.2 license. It is a 2-layer board measuring 43.2 × 48.9 mm, with 22 components from 12 distinct parts.
Its main chip is the ESP32-WROOM-E, from the ESP32 family. Other key parts include the HDC1080 and AMS1117-3.3. By type, the board carries 10 resistors, 6 capacitors, 3 ICs, 2 diodes and 1 connector.
It belongs with the iot & wireless designs in this gallery.
From the project
ESP32-IoT Base Board
ESP32-WROOM-32E based IoT development board for ESPHome designed with KiCad EDA
This board is still in it's early design phase...
- [x] Design basic PCB layout - [x] Generate fabrication data - [x] Fabicate prototypes - [ ] Test prototypes (rev. 0.2)
The intention was to use the ESP32-C3 SOC but arduino and esphome support for this generation of chips currently in an early stage and therfore the ESP32-WROOM-32E is used in the meantime.

Main components on the Esp32-iot base
Esp32-iot base bill of materials (BOM)
22 components, 12 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | HDC1080 | Texas_PWSON-N6 | U1 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U2 |
| 1 | ESP32-WROOM-E | ESP32-WROOM-32E | U5 |
| 1 | USB_C_Receptacle_USB2.0 | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1 |
| 1 | Power LED | LED_0603_1608Metric | D2 |
| 5 | 10uF | C_0603_1608Metric | C1, C2, C3, C5, C6 |
| 1 | 100nF | C_0603_1608Metric | C4 |
| 1 | 500 Ω | R_0603_1608Metric | R1 |
| 5 | 4.7 KΩ | R_0603_1608Metric | R2, R3, R6, R10, R11 |
| 3 | 10kΩ | R_0603_1608Metric | R5, R8, R9 |
| 1 | 10Ω | R_0603_1608Metric | R7 |
Esp32-iot base design files
The KiCad project lives in the mightea/esp32-iot-base repository on GitHub; these links point at the commit this page was built from.
- Layoutpcb/iotbase.kicad_pcb
- Schematicpcb/iotbase.kicad_sch
Esp32-iot base: common questions
What microcontroller does the Esp32-iot base use?
The Esp32-iot base is built around the ESP32-WROOM-E, from the ESP32 family.
How big is the Esp32-iot base PCB?
The Esp32-iot base measures 43.2 × 48.9 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32-iot base?
22 components, from 12 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32-iot base design files?
From the mightea/esp32-iot-base repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Esp32-iot base design in my own project?
Yes, under the terms of its CERN-OHL-1.2 license, which mightea chose for the repository.
Can I test firmware for the Esp32-iot base without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k