Hardware design
MiniGooseTM·hardware-design·wheel_robot_kicad/wheel_robot_kicad.kicad_sch

About the Hardware design PCB
Hardware design is an open source ESP32 PCB design by MiniGooseTM, published on GitHub. It is a board, with 10 components from 9 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1-N8R8, from the ESP32 family. Other key parts include the Mini360 and TB6612FNG. By type, the board carries 4 ICs, 4 resistors and 1 capacitor.
It belongs with the robotics & motion and power & battery designs in this gallery.
From the project
hardware part lists and circuitry
This repo contains the mechanical and electrical design of the MiniGoose robot. MiniGoose (also named Ryan the Gosling) is a 2-wheel differential drive balancing robot, which uses wheel encoders and IMU to stay upright and follow velocity commands. The robot is controlled by an onboard PPO policy, which outputs the PWM motor controls.
The robot is built from 2 N20 DC motors, wheel encoders, IMU, ESP-32, a battery, and 3D printed wheels and chassis. For a complete bill of materials, visit BOM. ## Repository structure
Main components on the Hardware design
Hardware design bill of materials (BOM)
10 components, 9 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | Mini360 | U4 | |
| 1 | TB6612FNG | SSOP-24_5.3x8.2mm_P0.65mm | U6 |
| 1 | ~ | BMI160_Module_SMD | U7 |
| 1 | ESP32-S3-DEVKITC-1-N8R8 | ESP32-S3-DEVKITC-1-N8R8 | U8 |
| 1 | 11.1V | 450mAh_3S_LiPo_BatteryPack_45C1 | |
| 1 | 100nF | C1 | |
| 1 | 100k | R1 | |
| 1 | 22k | R2 | |
| 2 | 6.8k | R3, R4 |
Hardware design design files
The KiCad project lives in the MiniGooseTM/hardware-design repository on GitHub; these links point at the commit this page was built from.
Hardware design: common questions
What microcontroller does the Hardware design use?
The Hardware design is built around the ESP32-S3-DEVKITC-1-N8R8, from the ESP32 family.
How many components are on the Hardware design?
10 components, from 9 distinct parts. The full bill of materials is listed on this page.
Where can I download the Hardware design design files?
From the MiniGooseTM/hardware-design repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Hardware design design in my own project?
The repository has no license, so all rights stay with MiniGooseTM. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Hardware design without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k