Dimmer
MitryKz·Dimmer
About the Dimmer PCB
Dimmer is an open source ESP32 PCB design by MitryKz, published on GitHub. It is a 2-layer board measuring 70 × 68 mm, with 51 components from 36 distinct parts.
Its main chip is the ESP32-WROOM-32D, from the ESP32 family. Other key parts include the LM75B, TLP185 and AMS1117-3.3. By type, the board carries 13 resistors, 8 connectors, 7 diodes, 5 capacitors, 4 ICs and 3 transistors.
Main components on the Dimmer
Dimmer bill of materials (BOM)
51 components, 36 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM75B | Diodes_SO-8 | U1 |
| 1 | ESP32-WROOM-32D | ESP32-WROOM-32 | U2 |
| 1 | TLP185 | SOIC-4_4.55x3.7mm_P2.54mm | U4 |
| 1 | AMS1117-3.3 | SOT-223-3_TabPin2 | U22 |
| 2 | IRFP460APBF | TO-247-3_Horizontal_TabDown | Q1, Q2 |
| 1 | BC807 | SOT-23 | Q3 |
| 1 | 220to12 | oblast_bp | J1 |
| 1 | Prog | 2pins | J2 |
| 1 | UART0 | 4pins | J3 |
| 2 | Conn_01x06 | PinHeader_1x06_P2.54mm_Vertical | J4, J16 |
| 1 | 220v_IN | OUT_IN(1) | J9 |
| 1 | 220v_OUT | OUT_IN(1) | J11 |
| 1 | SPI | PinHeader_1x04_P2.54mm_Vertical | J22 |
| 6 | Pin | polz_razjem | CLK1, CMD1, SD0, SD1, SD2, SD3 |
| 2 | SW_Push | aLIEXPRESS_BUTTON_G71Y | Mode1, RST2 |
| 1 | Rst | polz_razjem | RST1 |
| 2 | ADC | polz_razjem | S_VN1, S_VP1 |
| 2 | BAV99 | SOT-23 | D1, D2 |
| 1 | BZX84Cxx | D_SOT-23_ANK | D3 |
| 1 | 1N4148WT | D_SOD-523 | D4 |
Show 16 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | BLUE | LED_0805_2012Metric | D5 |
| 1 | RED | LED_0805_2012Metric | D6 |
| 1 | Fan3100tsx | SOT-23-5 | D7 |
| 1 | 0.01mk | C_0805_2012Metric | C1 |
| 1 | 0.47mk | C_0805_2012Metric | C2 |
| 1 | 100mk | C_1210_3225Metric | C4 |
| 1 | 0.1uF | C_0805_2012Metric | C8 |
| 1 | 1uF | C_0805_2012Metric | C11 |
| 1 | 2.2M | R_1206_3216Metric | R1 |
| 1 | 10k | R_0805_2012Metric | R2 |
| 1 | GL5528 | R_LDR_5.1x4.3mm_P3.4mm_Vertical | R3 |
| 2 | 120k 0.25W | R_0603_1608Metric | R4, R6 |
| 3 | 10k | R_0603_1608Metric | R5, R9, R13 |
| 1 | 220 1W | R_2512_6332Metric | R7 |
| 1 | 330k 0.25W | R_0603_1608Metric | R8 |
| 3 | 220 | R_1206_3216Metric | R10, R11, R12 |
Dimmer design files
The KiCad project lives in the MitryKz/Dimmer repository on GitHub; these links point at the commit this page was built from.
- LayoutDimmer.kicad_pcb
Dimmer: common questions
What microcontroller does the Dimmer use?
The Dimmer is built around the ESP32-WROOM-32D, from the ESP32 family.
How big is the Dimmer PCB?
The Dimmer measures 70 × 68 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Dimmer?
51 components, from 36 distinct parts. The full bill of materials is listed on this page.
Where can I download the Dimmer design files?
From the MitryKz/Dimmer repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Dimmer design in my own project?
The repository has no license, so all rights stay with MitryKz. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Dimmer without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k