STARTUP
mohamed1920said·STARTUP·hardware/central_gateway/central_gateway.kicad_pcb
About the STARTUP PCB
STARTUP is an open source ESP32 PCB design by mohamed1920said, published on GitHub. It is a 4-layer board measuring 130 × 77 mm, with 54 components from 35 distinct parts.
Its main chip is the ESP32-S3-DEVKITC-1-N8R8, from the ESP32 family. Other key parts include the RFM95W-868S2, R-78E5.0-1.0 and AP2112K-3.3TRG1. By type, the board carries 17 resistors, 10 connectors, 10 diodes, 7 capacitors, 4 ICs and 4 test points.
It belongs with the rf & radio and sensors designs in this gallery.
From the project
KiCad 10 carrier board for the AMR central gateway firmware. The board accepts an ESP32-S3-DevKitC-1-N8R8, adds a soldered RFM95W 868 MHz radio, protected sensor interfaces, regulated 7-18 V input, an enclosure-button connector, service UART, and test points.
KiCad 10 carrier board for the AMR central gateway firmware. The board accepts an ESP32-S3-DevKitC-1-N8R8, adds a soldered RFM95W 868 MHz radio, protected sensor interfaces, regulated 7-18 V input, an enclosure-button connector, service UART, and test points.
- Board revision: v1.1-prototype - Board size: 130 mm x 77 mm, including the ESP32 antenna clearance notch - Copper layers: 4 - Modular jack footprint: Wuerth Elektronik 615006138421, manufacturer geometry - Manufacturing outputs: manufacturing/centralgateway-fabrication.zip`
Main components on the STARTUP
STARTUP bill of materials (BOM)
54 components, 35 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-DEVKITC-1-N8R8 ESP32-S3-DevKitC-1-N8R8 | AMR_Central_ESP32-S3-DevKitC-1_Carrier | U1 |
| 1 | RFM95W-868S2 | AMR_Central_HOPERF_RFM95W_SMD | U2 |
| 1 | R-78E5.0-1.0 | AMR_Central_RECOM_R-78E5.0-1.0_SIP3 | U3 |
| 1 | AP2112K-3.3TRG1 AP2112K-3.3 | AMR_Central_SOT-23-5 | U4 |
| 1 | POWER 7-18V DC | AMR_Central_TerminalBlock_2 | J1 |
| 1 | 615006138421 RAIN RJ11 | AMR_Central_WR-MJ_615006138421 | J2 |
| 1 | 615006138421 WIND+VANE RJ11 | AMR_Central_WR-MJ_615006138421 | J3 |
| 1 | DHT11 | AMR_Central_TerminalBlock_3 | J4 |
| 1 | BMP280 I2C | AMR_Central_TerminalBlock_4 | J5 |
| 1 | PASSIVE LDR | AMR_Central_TerminalBlock_2 | J6 |
| 1 | BAT SENSE 0-6V | AMR_Central_TerminalBlock_2 | J7 |
| 1 | SERVICE UART | AMR_Central_Header_1x4 | J8 |
| 1 | SMA_868MHz | AMR_Central_SMA_Vertical_THT | J9 |
| 1 | PANEL SETUP BUTTON | AMR_Central_JST_XH_B2B-XH-A_1x02_P2.50mm | J10 |
| 1 | MF-MSMF075-2 PTC 0.75A | AMR_Central_Fuse_1812 | F1 |
| 1 | +5V | AMR_Central_TestPoint_THT | TP1 |
| 1 | +3V3 | AMR_Central_TestPoint_THT | TP2 |
| 1 | GND | AMR_Central_TestPoint_THT | TP3 |
| 1 | LORA_DIO1 | AMR_Central_TestPoint_THT | TP4 |
| 1 | GREEN | AMR_Central_LED_0805 | LED1 |
Show 15 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SMBJ18A | AMR_Central_D_SMB | D1 |
| 1 | SS34 | AMR_Central_D_SMA | D2 |
| 7 | PESD3V3U1BA PESD3V3 | AMR_Central_D_SOD323 | D3, D4, D5, D6, D7, D8, D9 |
| 1 | BZT52C6V2 | AMR_Central_D_SOD323 | D10 |
| 1 | 10uF 35V | AMR_Central_C_1210 | C1 |
| 1 | 22uF 10V | AMR_Central_C_1206 | C2 |
| 2 | 1UF 1uF | AMR_Central_C_0805 | C3, C4 |
| 1 | 10UF 10uF | AMR_Central_C_0805 | C5 |
| 2 | 100NF 100nF | AMR_Central_C_0805 | C6, C11 |
| 5 | 1k | AMR_Central_R_0805 | R1, R2, R4, R12, R14 |
| 4 | 10K 10k | AMR_Central_R_0805 | R3, R5, R13, R15 |
| 1 | 220R | AMR_Central_R_0805 | R6 |
| 3 | 4.7K 4.7k | AMR_Central_R_0805 | R7, R10, R11 |
| 2 | 100R | AMR_Central_R_0805 | R8, R9 |
| 2 | 100k 1% | AMR_Central_R_0805 | R16, R17 |
STARTUP design files
The KiCad project lives in the mohamed1920said/STARTUP repository on GitHub; these links point at the commit this page was built from.
STARTUP: common questions
What microcontroller does the STARTUP use?
The STARTUP is built around the ESP32-S3-DEVKITC-1-N8R8, from the ESP32 family.
How big is the STARTUP PCB?
The STARTUP measures 130 × 77 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the STARTUP?
54 components, from 35 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the STARTUP design files?
From the mohamed1920said/STARTUP repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the STARTUP design in my own project?
The repository has no license, so all rights stay with mohamed1920said. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the STARTUP without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k