HardLabs

D2000-m.2-EC

mothenjoyer69·pcb-design-files·D2000-m.2-EC/D2000-m.2-EC.kicad_pcb

D2000-m.2-EC PCB layout, top view — open source RP2040/RP2350 board by mothenjoyer69

About the D2000-m.2-EC PCB

D2000-m.2-EC is an open source RP2040/RP2350 PCB design by mothenjoyer69, published on GitHub under the MIT license. It is a 4-layer board measuring 26 × 40 mm, with 39 components from 21 distinct parts.

Its main chip is the QFN-80-1EP_10x10mm_P0.4mm_EP3.4x3.4mm_ThermalVias, from the RP2040/RP2350 family. Other key parts include the AP2112K-3.3 and W25Q32JVSS. By type, the board carries 18 capacitors, 10 resistors, 4 ICs, 2 switches, 2 diodes and 1 crystal.

Main components on the D2000-m.2-EC

AP2112K-3.3W25Q32JVSS

D2000-m.2-EC bill of materials (BOM)

39 components, 21 distinct parts.

QtyPartRefs
1
~
U1
1
~
U2
1
AP2112K-3.3
U3
1
W25Q32JVSS
U4
1
12MHz
Y1
1
USB_C_Receptacle
J1
1
RUN
SW1
1
USB_BOOT
SW2
1
PWR
D1
1
USR
D2
1
3.3u
L1
11
100n
C1, C2, C3, C4, C5, C6, C7, C8 +3
4
4.7u
C11, C16, C17, C18
1
100n
C13
2
22pF
C14, C15
2
1.5k
R1, R2
3
27r
R3, R4, R5
1
10k
R6
2
1K
R7, R9
1
0r
R8
Show 1 more
QtyPartRefs
1
33r
R13

D2000-m.2-EC design files

The KiCad project lives in the mothenjoyer69/pcb-design-files repository on GitHub; these links point at the commit this page was built from.

D2000-m.2-EC: common questions

What microcontroller does the D2000-m.2-EC use?

The D2000-m.2-EC is built around the QFN-80-1EP_10x10mm_P0.4mm_EP3.4x3.4mm_ThermalVias, from the RP2040/RP2350 family.

How big is the D2000-m.2-EC PCB?

The D2000-m.2-EC measures 26 × 40 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the D2000-m.2-EC?

39 components, from 21 distinct parts. The full bill of materials is listed on this page.

Where can I download the D2000-m.2-EC design files?

From the mothenjoyer69/pcb-design-files repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the D2000-m.2-EC design in my own project?

Yes, under the terms of its MIT license, which mothenjoyer69 chose for the repository.

Can I test firmware for the D2000-m.2-EC without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in pcb-design-files

Similar boards