Drivedot
MrWxlfz·drivedot·hardware/pcb/drivedot.kicad_pcb
About the Drivedot PCB
Drivedot is an open source ESP32 PCB design by MrWxlfz, published on GitHub under the MIT license. It is a 2-layer board measuring 60 × 40 mm, with 6 components from 5 distinct parts.
Its main chip is the XIAO ESP32S3, from the ESP32 family. By type, the board carries 2 connectors, 2 resistors, 1 IC and 1 switch.
It belongs with the displays & leds and sensors designs in this gallery.
From the project
for hc halflife
This is an actual two-layer KiCad design with a routed PCB, schematic, Gerbers and drill files. It is an unbuilt prototype design. Electrical and design-rule checks pass; received-part fit, assembly, power-up and driving measurements have not been tested.
Open drivedot.kicadpro in KiCad 9**. The project-local symbols, footprints and library tables are included. There are no library downloads needed to edit this board.

Main components on the Drivedot
Drivedot bill of materials (BOM)
6 components, 5 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | XIAO ESP32S3 | XIAO_Socket | U1 |
| 1 | OLED / SSD1306 | Header_1x04 | J1 |
| 1 | GY-521 / MPU6050 | Header_1x04 | J2 |
| 1 | Start / stop | Tactile_6mm | SW1 |
| 2 | 4.7k DNP | R_Axial_P7.62 | R1, R2 |
Drivedot design files
The KiCad project lives in the MrWxlfz/drivedot repository on GitHub; these links point at the commit this page was built from.
Drivedot: common questions
What microcontroller does the Drivedot use?
The Drivedot is built around the XIAO ESP32S3, from the ESP32 family.
How big is the Drivedot PCB?
The Drivedot measures 60 × 40 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Drivedot?
6 components, from 5 distinct parts. The full bill of materials is listed on this page.
Where can I download the Drivedot design files?
From the MrWxlfz/drivedot repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Drivedot design in my own project?
Yes, under the terms of its MIT license, which MrWxlfz chose for the repository.
Can I test firmware for the Drivedot without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k