11 open source boards using the XIAO_ESP32S3
Real designs built with the XIAO_ESP32S3, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Piyopiyo
piyopiyoex
100 × 56 mm49 parts2LCC-BY-4.05ESP32
Drivedot
MrWxlfz
60 × 40 mm6 parts2LMIT1ESP32
TechnicalDocs openUC2-QBox
openUC2
106 × 46 mm149 parts4LNo license0Hackpad v2
Catsarepro21
84 × 78 mm67 parts2LNo license0PinaBioHw
AlejandroPina
110 × 70 mm49 parts2LNo license0ESP32
ESP32S3 Snifar
jtsuka
95 × 70 mm39 parts2LNo license0Solar cyber
tornapart0
60 × 50 mm12 parts2LNo license0- schematic only · 17 partsESP32
Hotpot table
rahuljeyaraj
17 partsMIT0 - schematic only · 13 partsESP32
Esp32-music player battery
eriksalo
13 partsNo license0 ESP32
TC Interface Board
jtsuka
68.9 × 121.6 mm30 parts2LNo license0ESP32
TC106 Overall circuit diagram
jtsuka
68.9 × 121.6 mm30 parts2LNo license0
How designs wire the XIAO_ESP32S3
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the XIAO_ESP32S3 connects to, and the resistors, capacitors and other passives placed on it.
- The 3V3 pin is tied to 3.3V on 7 of 7 designs.
- The PA02_A0_D0 pin has a series resistor on 3 of 7 designs, most often 10 kΩ (then 1 kΩ).
- The PA8_A4_D4_SDA pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
- The PA9_A5_D5_SCL pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| PA02_A0_D0pin 1 | Connected to: Signal 71% |
|
| PA8_A4_D4_SDApin 5 | Connected to: A connector 71% |
|
| PA9_A5_D5_SCLpin 6 | Connected to: A connector 71% |
|
| 3V3pin 12 | Connected to: 3.3V 100% | — |
| GNDpin 13 | Connected to: GND 100% | — |
9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Piyopiyo pcb by piyopiyoex, Drivedot by MrWxlfz, PinaBioHw by AlejandroPina and Hackpad v2 by Catsarepro21.
The XIAO_ESP32S3 in open source designs
The gallery holds 11 open source boards using the XIAO_ESP32S3 from 9 GitHub repositories; a typical one measures about 84 × 70 mm and carries around 30 components.
89% are two-layer designs, the rest use four layers or more, and 27% carry an open source license.
The most starred is Piyopiyo pcb by piyopiyoex.
Microcontrollers on boards using the XIAO_ESP32S3
What boards using the XIAO_ESP32S3 are built for
XIAO_ESP32S3: common questions
Where can I find a XIAO_ESP32S3 reference design?
Each of the 11 boards on this page is a real design using the XIAO_ESP32S3. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the XIAO_ESP32S3 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the XIAO_ESP32S3.
What resistor goes on the XIAO_ESP32S3 PA02_A0_D0 pin?
The PA02_A0_D0 pin has a series resistor on 3 of 7 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 7 open source designs using the XIAO_ESP32S3.
What pull-up resistor is used on the XIAO_ESP32S3 PA8_A4_D4_SDA pin?
The PA8_A4_D4_SDA pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ (then 4.7 kΩ). Counted from the KiCad layouts of 7 open source designs using the XIAO_ESP32S3.
Which microcontrollers do boards using the XIAO_ESP32S3 use?
Most are built on ESP32 (8).
How big is a typical board using the XIAO_ESP32S3?
The median is 84 × 70 mm, and 89% are two-layer designs.
What is the most popular open source board using the XIAO_ESP32S3?
By GitHub stars, Piyopiyo pcb by piyopiyoex, with 5 stars.
Can I simulate one of these boards using the XIAO_ESP32S3 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.