Module tester board
About the Module tester board
Module tester board is an open source AVR/Arduino PCB design by MST-Robotics, published on GitHub. It is a 2-layer board measuring 69.1 × 53.3 mm, with 29 components from 23 distinct parts.
Its main chip is the Arduino_Nano_v3.x, from the AVR/Arduino family. Other key parts include the LT8330, L7805, MCP2515-EST and ATA6560,1. By type, the board carries 9 capacitors, 7 resistors, 4 ICs, 3 connectors, 2 diodes and 1 module.
From the project
This repository holds the electrical schematics and board layouts for the ROV (TITAN II) being built by the Missouri University of Science and Technology Underwater Robotics Design Team.
Main components on the Module tester board
Module tester board bill of materials (BOM)
29 components, 23 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LT8330 | TSOT-23_S6 | U1 |
| 1 | L7805 | SOT-223 | U2 |
| 1 | MCP2515-EST | TSSOP-20_4.4x6.5mm_P0.65mm | U4 |
| 1 | ATA6560,1 | SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | Arduino_Nano_v3.x | Arduino_Nano | A1 |
| 1 | 20MHz | Crystal_SMD_0603-2Pin_6.0x3.5mm | Y1 |
| 1 | Conn_01x09 | PinHeader_1x09_P2.54mm_Vertical | J1 |
| 1 | Barrel_Jack | CUI_PJ-037A | J2 |
| 1 | Conn_01x04_Male | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | SW_DIP_x04 | SW_DIP_SPSTx04_Slide_9.78x12.34mm_W7.62mm_P2.54mm | SW1 |
| 1 | D_Schottky | D_SOD-123F | D1 |
| 1 | 1N4007 | D_0603_1608Metric | D2 |
| 1 | 6.8u | L_0603_1608Metric | L1 |
| 2 | 4.7u | C_0603_1608Metric | C1, C4 |
| 1 | 4.7p | C_0603_1608Metric | C2 |
| 1 | 1u | C_0603_1608Metric | C3 |
| 2 | 15p | C_0603_1608Metric | C5, C6 |
| 1 | 1uF | C_0603_1608Metric | C7 |
| 2 | 100uF | CP_Radial_D5.0mm_P2.50mm | C8, C9 |
| 2 | 1M | R_0603_1608Metric | R1, R2 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 34.8k | R_0603_1608Metric | R3 |
| 3 | 10k | R_0603_1608Metric | R4, R5, R7 |
| 1 | 100k | R_0603_1608Metric | R6 |
Module tester board design files
The KiCad project lives in the MST-Robotics/TITAN-Electrical repository on GitHub; these links point at the commit this page was built from.
Module tester board: common questions
What microcontroller does the Module tester board use?
The Module tester board is built around the Arduino_Nano_v3.x, from the AVR/Arduino family.
How big is the Module tester board?
The Module tester board measures 69.1 × 53.3 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Module tester board?
29 components, from 23 distinct parts. The full bill of materials is listed on this page.
Where can I download the Module tester board design files?
From the MST-Robotics/TITAN-Electrical repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Module tester board design in my own project?
The repository has no license, so all rights stay with MST-Robotics. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Module tester board without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in TITAN-Electrical
AVR/ArduinoPower board
171.8 × 117.7 mm80 parts2LNo license0
AVR/ArduinoMain board
81.6 × 88.6 mm67 parts2LNo license0
Control station board
68.6 × 43.8 mm41 parts2LNo license0
AVR/ArduinoProofOfConceptBoardV1
86 × 45.2 mm40 parts2LNo license0
AVR/ArduinoGimble Goblin
44.5 × 36.6 mm28 parts2LNo license0
ProgrammerBoard
27.4 × 25.4 mm11 parts2LNo license0
Similar boards
AVR/ArduinoMagspoof
samyk
35 × 29 mm11 parts2LNo license4.2k
AVR/ArduinoRedox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0k
AVR/ArduinoLabrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2k
AVR/ArduinoModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoV4
30 × 50 mm38 parts2LCC-BY-NC-4.01.1k
AVR/ArduinoDiscipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k