Parkbrake

mumme74·CarTransporter·electronics/Parkbrake/Parkbrake.kicad_pcb

Parkbrake PCB layout, top view — open source STM32 board by mumme74
Simulate this board

About the Parkbrake PCB

Parkbrake is an open source STM32 PCB design by mumme74, published on GitHub. It is a 2-layer board measuring 101.6 × 114.3 mm, with 353 components from 91 distinct parts.

Its main chip is the STM32F373RBTx, from the STM32 family. Other key parts include the 74LVC00, 74LVC08, LM2903, IRS2304 and ZXCT1082. By type, the board carries 120 resistors, 101 capacitors, 41 diodes, 35 ICs, 33 transistors and 14 jumpers.

From the project

Electronics systems for a car transporter

This repository is for the electronics systems used to make car transporter

Parkbrake, from the project README
From the project README

Main components on the Parkbrake

Parkbrake bill of materials (BOM)

353 components, 91 distinct parts.

QtyPartRefs
2
74LVC00
U1, U3
3
74LVC08
U2, U4, U35
4
LM2903
U5, U9, U13, U17
8
IRS2304
U6, U8, U10, U12, U14, U16, U18, U20
4
ZXCT1082
U7, U11, U15, U19
1
MIC2619
U21
1
MC34063
U22
1
LD1117S33CTR
U23
1
CAT25160_EEPROM
U24
1
STM32F373RBTx
U25
1
SN65HVD1050D
U26
1
SN74LVC245ADBR
U27
1
SN74HC20
U28
1
SN74HC02
U29
1
SN74HC132
U30
2
MAX232
U31, U32
2
NCV1124
U33, U34
3
BSS138
Q1, Q2, Q31
2
P-ch -40V 0.0035ohm
Q3, Q4
2
BSS308
Q5, Q6
Show 71 more
QtyPartRefs
9
NX3008CBKS
Q7, Q12, Q13, Q18, Q19, Q24, Q25, Q30 +1
16
IPD031N06L3 G
Q8, Q9, Q10, Q11, Q14, Q15, Q16, Q17 +8
1
NTS4173
Q32
1
24Mhz
Y1
1
Conn48pin
P1
1
JTAG
P2
1
UART
P3
1
BOOT0
JP1
1
Jumper_NO_Small
JP2
1
soft_L_out+
JP3
1
L_passth+
JP4
1
LF+_to_in
JP5
1
soft_L_out-
JP6
1
L_passth-
JP7
1
LF-_to_in
JP8
1
soft_R_out+
JP9
1
RF_passth+
JP10
1
RF+_to_in
JP11
1
soft_R_out-
JP12
1
RF_passth-
JP13
1
RF-_to_in
JP14
3
VR
VR1, VR2, VR3
3
10v
D1, D2, D5
22
1n4148w
D3, D4, D14, D15, D16, D17, D18, D19 +14
1
LF_Release
D6
1
LF_Tighten
D7
1
LR_Release
D8
1
LR_Tighten
D9
1
RF_Release
D10
1
RF_tighten
D11
1
RR_Release
D12
1
RR_Tighten
D13
1
min 40V 1A
D26
1
min 1.5A
D27
6
3.3V
D28, D29, D31, D32, D33, D34
1
10uH
L1
1
33uH
L2
42
100n
C1, C2, C3, C4, C5, C6, C9, C11 +34
28
1u
C7, C10, C14, C17, C21, C24, C28, C31 +20
4
220nF
C8, C15, C22, C29
1
470p
C35
1
10u
C36
1
680u
C38
5
10u
C40, C41, C92, C93, C100
6
1n
C43, C58, C63, C96, C97, C99
2
26p
C44, C45
1
4.7u
C46
4
10n
C49, C51, C53, C55
2
33uF
C72, C73
4
47n
C83, C84, C85, C86
43
10k
R1, R2, R5, R10, R11, R12, R13, R16 +35
10
1k
R3, R4, R6, R7, R8, R9, R84, R99 +2
16
10
R14, R15, R25, R26, R31, R32, R42, R43 +8
4
43
R17, R34, R51, R68
8
100
R19, R23, R36, R40, R53, R57, R70, R74
16
0.002
R20, R21, R22, R24, R37, R38, R39, R41 +8
1
0.150 1/2W
R79
2
220k
R80, R82
1
12k
R81
1
3k
R85
1
255
R87
1
120
R89
2
330
R92, R93
1
560
R102
1
2.2k
R103
2
1k
R104, R110
1
100k
R105
1
2k
R107
2
1M
R108, R109
4
15k
R111, R112, R113, R114
2
16.9k
R115, R116

Parkbrake design files

The KiCad project lives in the mumme74/CarTransporter repository on GitHub; these links point at the commit this page was built from.

Parkbrake: common questions

What microcontroller does the Parkbrake use?

The Parkbrake is built around the STM32F373RBTx, from the STM32 family.

How big is the Parkbrake PCB?

The Parkbrake measures 101.6 × 114.3 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Parkbrake?

353 components, from 91 distinct parts. The full bill of materials is listed on this page.

Where can I download the Parkbrake design files?

From the mumme74/CarTransporter repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Parkbrake design in my own project?

The repository has no license, so all rights stay with mumme74. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Parkbrake without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in CarTransporter

Similar boards