26 open source boards using the LM2903
Real designs built with the LM2903, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
TI99 22
danwerner21
350 × 224.3 mm242 parts2LNo license50AVR/Arduino
ATMEGA328-Motor-Board
AntonioMR
77 × 100 mm171 parts2LNo license39BSPD
SDU-Vikings
100 × 50 mm84 parts2LCC0-1.030STM32
Parkbrake
mumme74
101.6 × 114.3 mm353 parts2LNo license7PIC
PlantWateringDevice
RobertGawron
48 × 45 mm44 parts4LMIT5ESP32
TI99 22
danwerner21
244 × 244 mm257 parts4LNo license4FPGA
Output.panel 3x3
Roboy
217 × 139 mm129 parts4LBSD-3-Clause4Intel 8088 Computer
oberrow
100 × 100 mm64 parts4LMIT1KnurDash
chrumck
55 × 34 mm23 parts2LMIT1STM32
S105
rusefi
86 × 159 mm583 parts2LNo license0Main
yminp
148.6 × 82 mm156 parts2LCERN-OHL-W-2.00Instru bab v2 full
trublion
110 × 85 mm141 parts2LMIT0STM32
Menelaos rev-4
acastles91
99.5 × 91 mm124 parts4LNo license0ESP32
Power Systems
nick19curtin
367.8 × 97.5 mm113 parts2LNo license0STM32
MareapPowerBoard
RandBeyy
90 × 70 mm69 parts2LNo license0- schematic only · 24 partsESP32
Ocatvia-Carbon I-C Challenge
Hokkyokuse1
24 partsNo license0 FPGA
Panel 3x3
Roboy
217 × 139 mm129 parts4LBSD-3-Clause4Usb sniffer h7p20
vllogic
47.5 × 47.5 mm124 parts4LNo license3Instru bab v2 main
trublion
110 × 85 mm129 parts2LMIT0Microbot(2024-10-31 160842)
Freimor
90 × 110 mm128 parts4LNo license0FPGA
Board
Roboy
65 × 39 mm128 parts4LBSD-3-Clause4Usb sniffer 2
vllogic
57.7 × 47.5 mm123 parts4LNo license3Td hv
tdaede
90 × 71 mm60 parts2LNo license370Carte Alim
robotronik
102.9 × 70.5 mm58 parts2LNo license1Carte Alim
robotronik
102.9 × 70.5 mm58 parts2LNo license1STM32
EP5 rearbox
NTURacingTeam
149 × 79.5 mm229 parts2LNo license4
How designs wire the LM2903
Read from the KiCad layouts of 21 open source designs, one per repository: what each pin of the LM2903 connects to, and the resistors, capacitors and other passives placed on it.
- The V- pin is tied to GND on 18 of 21 designs (a signal on 2).
- The - pins have a series resistor on 11 of 21 designs, most often 10 kΩ (then 1 kΩ).
- The + pins have a resistor to GND on 11 of 21 designs, most often 100 kΩ (then 20 mΩ).
- The - pins have a resistor to GND on 10 of 21 designs, most often 1 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SSTXBpin 1 | Connected to: The microcontroller 24% |
|
| -pin 2, 6 | Connected to: Signal 79% · not connected 17% |
|
| +pin 3, 5 | Connected to: Signal 74% |
|
| V-pin 4 | Connected to: GND 86% | — |
| VDDKpin 7 | Connected to: Signal 62% · not connected 33% |
|
| V+pin 8 | Connected to: 5V 76% · a signal 19% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Td hv by tdaede, TI99 22 by danwerner21, ATMEGA328-Motor-Board by AntonioMR and BSPD by SDU-Vikings.
The LM2903 in open source designs
The gallery holds 26 open source boards using the LM2903 from 22 GitHub repositories; a typical one measures about 100 × 85 mm and carries around 126 components.
60% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Td hv by tdaede.
Parts used alongside the LM2903
Microcontrollers on boards using the LM2903
What boards using the LM2903 are built for
LM2903: common questions
Where can I find a LM2903 reference design?
Each of the 26 boards on this page is a real design using the LM2903. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM2903 V- pin connected?
The V- pin is tied to GND on 18 of 21 designs (a signal on 2). Counted from the KiCad layouts of 21 open source designs using the LM2903.
What resistor goes on the LM2903 - pin?
The - pins have a series resistor on 11 of 21 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 21 open source designs using the LM2903.
What resistor goes on the LM2903 + pin?
The + pins have a resistor to GND on 11 of 21 designs, most often 100 kΩ (then 20 mΩ). Counted from the KiCad layouts of 21 open source designs using the LM2903.
What parts are used alongside the LM2903?
The LM2902, TL072, 27C64, 74HC00 and 74HC04 appear in the most repositories here.
Which microcontrollers do boards using the LM2903 use?
Most are built on STM32 (5), ESP32 (3), FPGA (3) and AVR/Arduino (1).
How big is a typical board using the LM2903?
The median is 100 × 85 mm, and 60% are two-layer designs.
What is the most popular open source board using the LM2903?
By GitHub stars, Td hv by tdaede, with 370 stars.
Can I simulate one of these boards using the LM2903 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.