PoE-FanController

nielsverhoeven·PoE-FanController·hardware/kicad/PoE-FanController.kicad_pcb

PoE-FanController PCB layout, top view — open source ESP32 board by nielsverhoeven

About the PoE-FanController PCB

PoE-FanController is an open source ESP32 PCB design by nielsverhoeven, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 95 × 79 mm, with 33 components from 19 distinct parts.

Its main chip is the PPPC202LFBN-RC, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 17 resistors, 6 connectors, 4 diodes, 3 LEDs, 1 IC and 1 capacitor.

It belongs with the power & battery and dev boards & breakouts designs in this gallery.

From the project

A PoE 802.3at (25.5 W) powered quad-fan controller using the Waveshare ESP32-P4-ETH development board (SKU 32086) mounted HAT-style on a custom carrier PCB. The carrier handles PoE power extraction and 12 V fan outputs; the Waveshare module integrates the ESP32-P4NRW32 SoC, LAN87

A PoE 802.3at (25.5 W) powered quad-fan controller using the Waveshare ESP32-P4-ETH development board (SKU 32086) mounted HAT-style on a custom carrier PCB. The carrier handles PoE power extraction and 12 V fan outputs; the Waveshare module integrates the ESP32-P4NRW32 SoC, LAN8720A Ethernet PHY (RMII), CH343P USB-UART bridge, USB-C connector, and 32 MB flash + 32 MB PSRAM. Provides wired Ethernet for reliable data-centre and server-room deployments.

Main components on the PoE-FanController

PoE-FanController bill of materials (BOM)

33 components, 19 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
DHT11
U1
1
47053-1000
FAN1
Molex
J2
1
47053-1000
FAN2
Molex
J3
1
47053-1000
FAN3
Molex
J4
1
47053-1000
FAN4
Molex
J5
1
JST 3pin
J6
1
PPPC202LFBN-RC
Waveshare_ESP32P4POEETH
Sullins
J8
1
DC-Boost-Module
U_BOOST1
1
150060GS75000
LED_GREEN
Wurth
LED1
1
150060AS75000
LED_ORANGE
Wurth
LED2
1
LED_GREEN
LED6
4
150060GS75000
LED_GREEN
Wurth
D2, D3, D4, D5
1
0.1uF
C1
2
4k7
R1, R14
4
0R
R2, R4, R16, R17
2
MFR-25FBF52-330R
330R
Yageo
R3, R13
4
MFR-25FBF52-10K0
10k
Yageo
R5, R6, R7, R8
4
MFR-25FBF52-1K00
150R
Yageo
R9, R10, R11, R12
1
330R
R15

PoE-FanController design files

The KiCad project lives in the nielsverhoeven/PoE-FanController repository on GitHub; these links point at the commit this page was built from.

PoE-FanController: common questions

What microcontroller does the PoE-FanController use?

The PoE-FanController is built around the PPPC202LFBN-RC, from the ESP32 family.

How big is the PoE-FanController PCB?

The PoE-FanController measures 95 × 79 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the PoE-FanController?

33 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the PoE-FanController design files?

From the nielsverhoeven/PoE-FanController repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the PoE-FanController design in my own project?

Yes, under the terms of its GPL-3.0 license, which nielsverhoeven chose for the repository.

Can I test firmware for the PoE-FanController without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards