Elettrica-VS
norcenw·Elettrica-VS
About the Elettrica-VS PCB
Elettrica-VS is an open source ESP32 PCB design by norcenw, published on GitHub. It is a board, with 26 components from 16 distinct parts.
Its main chip is the ESP32-S3, from the ESP32 family. Other key parts include the TB6600, CONVERTITORE DC-DC, CD4066BPW, EA_T123X-I2C and Lettore microSD. By type, the board carries 13 ICs, 4 modules, 4 connectors, 1 relay and 1 switch.
Main components on the Elettrica-VS
Elettrica-VS bill of materials (BOM)
26 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | TB6600 | SSOP-24_5.3x8.2mm_P0.65mm | U1, U2, U3, U4 |
| 2 | ESP32-S3 | QFN-56-1EP_7x7mm_P0.4mm_EP4x4mm | U5, U8 |
| 4 | CONVERTITORE DC-DC | TO-263-5_TabPin3 | U6, U7, U9, U12 |
| 1 | CD4066BPW | TSSOP-14_4.4x5mm_P0.65mm | U10 |
| 1 | EA_T123X-I2C | EA_T123X-I2C | U11 |
| 1 | Lettore microSD | EA_T123X-I2C | U13 |
| 2 | Raspberry_Pi_5 | Adafruit_Feather | A1, A2 |
| 1 | Stepper_Motor_bipolar | M1 | |
| 1 | Fan | M2 | |
| 2 | Camera | J1, J2 | |
| 2 | Schermo | J3, J4 | |
| 1 | NC | Fungo1 | |
| 1 | FINDER-30.22 | Relay_DPDT_Finder_30.22 | K2 |
| 1 | TPP-15-112-D | Converter_ACDC_TRACO_TPP-15-1xx-D_THT | PS1 |
| 1 | SW_DIP_x02 | SW1 | |
| 1 | NO | Start1 |
Elettrica-VS design files
The KiCad project lives in the norcenw/Elettrica-VS repository on GitHub; these links point at the commit this page was built from.
- Schematicschema_r3.kicad_sch
Elettrica-VS: common questions
What microcontroller does the Elettrica-VS use?
The Elettrica-VS is built around the ESP32-S3, from the ESP32 family.
How many components are on the Elettrica-VS?
26 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Elettrica-VS design files?
From the norcenw/Elettrica-VS repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Elettrica-VS design in my own project?
The repository has no license, so all rights stay with norcenw. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Elettrica-VS without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
Open Book Abridged Edition
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k