Starbie-PCB-Design
npsboy·Starbie-PCB-Design
About the Starbie-PCB-Design
Starbie-PCB-Design is an open source ESP32 PCB design by npsboy, published on GitHub. It is a 2-layer board measuring 98 × 98.8 mm, with 7 components from 6 distinct parts.
Its main chip is the XIAO-ESP32-C3-SMD, from the ESP32 family. Other key parts include the DHT11. By type, the board carries 2 ICs, 2 connectors, 2 switches and 1 resistor.
It belongs with the keyboards, sensors and iot & wireless designs in this gallery.
From the project
A small KiCad PCB project: a handheld board built around a Seeed XIAO ESP32-C3, with an I2C OLED display (128x64), an MPU6050 motion sensor (GY-521), and push buttons (Cherry MX switches).
A small KiCad PCB project: a handheld board built around a Seeed XIAO ESP32-C3, with an I2C OLED display (128x64), an MPU6050 motion sensor (GY-521), and push buttons (Cherry MX switches).
Full BOM with vendor links and notes: Starbie_BOM.csv (prices in USD, vendors in India).
- Starbie.kicadsch / Starbie.kicadpcb / Starbie.kicadpro: KiCad project files - libs/: custom symbols, footprints and 3D models - gerbers/, StarbieGerbers.zip: manufacturing outputs - StarbieBOM.csv: bill of materials with vendors and prices (India) - StarbieCPL.csv: component placement list for PCB assembly -…

Main components on the Starbie-PCB-Design
Starbie-PCB-Design bill of materials (BOM)
7 components, 6 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DHT11 | Aosong_DHT11_5.5x12.0_P2.54mm | U1 |
| 1 | XIAO-ESP32-C3-SMD | XIAO-ESP32-C3-SMD | U2 |
| 1 | OLED | Display_128x64_096_I2C | J1 |
| 1 | MPU6050 | MPU6050_Module | J2 |
| 2 | SW_Push | SW_Cherry_MX_1.00u_PCB | SW1, SW2 |
| 1 | 10k | R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1 |
Starbie-PCB-Design design files
The KiCad project lives in the npsboy/Starbie-PCB-Design repository on GitHub; these links point at the commit this page was built from.
- LayoutStarbie.kicad_pcb
- SchematicStarbie.kicad_sch
- BOMREADME.md
Starbie-PCB-Design: common questions
What microcontroller does the Starbie-PCB-Design use?
The Starbie-PCB-Design is built around the XIAO-ESP32-C3-SMD, from the ESP32 family.
How big is the Starbie-PCB-Design?
The Starbie-PCB-Design measures 98 × 98.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Starbie-PCB-Design?
7 components, from 6 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Starbie-PCB-Design design files?
From the npsboy/Starbie-PCB-Design repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Starbie-PCB-Design design in my own project?
The repository has no license, so all rights stay with npsboy. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Starbie-PCB-Design without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k