Softswitcher

oldsheeep3·TheHack·softswitcher/softswitcher.kicad_pcb

Softswitcher PCB layout, top view — open source Raspberry Pi board by oldsheeep3

About the Softswitcher PCB

Softswitcher is an open source Raspberry Pi PCB design by oldsheeep3, published on GitHub under the GPL-2.0 license. It is a 2-layer board measuring 78 × 78 mm, with 29 components from 8 distinct parts.

Its main chip is the RaspberryPi_Pico_W, from the Raspberry Pi family. Other key parts include the CH224K. By type, the board carries 16 diodes, 8 switches, 2 resistors, 1 IC, 1 module and 1 connector.

It belongs with the iot & wireless designs in this gallery.

From the project

HybridSwitcher — ハイブリッドIP映像スイッチャー(開発用リポジトリ)

既存機材(ATEM Mini)と自作ハードウェア(自作スイッチングモジュール群 + Pico 2W)、 ネットワーク技術(SRT / NDI / WebAPI)を融合した、次世代のハイブリッドIP映像スイッチャーシステム。

PC上に常駐する制御アプリを「脳」とし、複数プロトコル(UVC / NDI / SRT)の映像入力・PiP合成・ 仮想カメラ出力・タリー送出・外部機材(ATEM)の遠隔制御を一元化する。DIYでありながらプロ用 スイッチャーに匹敵する多人数オペレーション(メイン/サブ分業)と拡張性を目指す。

clone しただけの状態では、次の理由で初回ビルドが必ず落ちる。setup.sh がこれを一括で潰す。

未解決の問題が残ると終了コード 1 で終わるので、CI からそのまま呼べる(./setup.sh --ci)。

Main components on the Softswitcher

Softswitcher bill of materials (BOM)

29 components, 8 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
CH224K
U1
1
RaspberryPi_Pico_W
A1
1
USB_C_RECEPTACLE_USB2.0_14P
USB_C_Receptacle_USB2.0_14P
J1
8
CherryMX
SW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8
8
1N4148W
D1, D2, D5, D6, D9, D10, D13, D14
8
SK6812MINI-E
D3, D4, D7, D8, D11, D12, D15, D16
1
1k
R1
1
10K
10k
R2

Softswitcher design files

The KiCad project lives in the oldsheeep3/TheHack repository on GitHub; these links point at the commit this page was built from.

Softswitcher: common questions

What microcontroller does the Softswitcher use?

The Softswitcher is built around the RaspberryPi_Pico_W, from the Raspberry Pi family.

How big is the Softswitcher PCB?

The Softswitcher measures 78 × 78 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Softswitcher?

29 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Softswitcher design files?

From the oldsheeep3/TheHack repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Softswitcher design in my own project?

Yes, under the terms of its GPL-2.0 license, which oldsheeep3 chose for the repository.

Can I test firmware for the Softswitcher without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

More boards in TheHack

Similar boards